Emerson Process Management Water Dispenser warranty Safety Symbols Important Safety Information

Division of Emerson Electric Co.

Racine, Wisconsin 53406, U.S.A.

In-Sink-Erator

Instant Hot Water Dispenser

Installation, Care & Use Guide

Congratulations on the purchase of your new In-Sink-Erator instant hot water dispenser. This product is designed and manufactured to the highest standards.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Connecting the dispenser to your regular water supplies requires no special plumbing. All details are covered in the installations instructions. Be sure that the plumbing connections conform to your applicable local codes. If your water supply contains sand, grit or other suspended particles, the use of a filter is recommended. The filter should not result in the water pressure to the dispenser dropping below 30 pounds per square inch (207kPa). This will prevent your unit from operating properly.

A standard 115-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power. The current use is 6.5 amps only when the tank is heating. Ensure that all electrical wiring and connections conform to applicable codes. Note: The wall outlet to your dispenser must have power supplied to it continuously and must be fused. It should not be controlled by the same wall switch that operates your disposer.

SAFETY SYMBOLS!

The warning symbol alerts you to potential hazards or unsafe practices which could result in severe personal injury or death.

The caution symbol alerts you to hazards or unsafe practices which could result in minor personal injury or property damage.

IMPORTANT SAFETY INFORMATION!

This product dispenses water at approximately 190˚F, which is hot enough to cause severe burns. Caution should be exercised when installing and using this product.Do not allow children to operate this appliance without adult supervision.

Do not attempt to install the unit until you have read and understand these installation guide instructions.

Under no circumstances is this product to be altered in any way other than that which is specifically addressed in these instructions. Doing so may void your warranty.

Do not use an electric drill to drill into metal water pipes; doing so could result in an electrical shock hazard. If necessary, use a cordless drill or hand drill.

Premature connection of the unit to an electrical supply could result in a “dry start” condition, which could damage the unit and void your warranty. The unit must be completely installed and the tank must be completely full with water running from the dispenser before plugging the unit in to an electrical supply. Consult these installation instructions.

Personal Injury

•Dispenses 190˚F (88˚C) water which can instantly cause scalds or burns. Use care when operating this appliance.

•Do not allow children to operate this appliance without adult supervision.

Fire Hazard

•To minimize possibility of fire, do not store flammable items such as rags, paper or aerosol cans near the tank. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Personal Injury

•This tank is a non-pressure tank. Do not modify this system. Do not close vent tube or connect other type faucets or valves to the tank.

•Use only the faucet supplied.

Electrical Shock Hazard

•Disconnect power before installing or servicing unit.

•Use only a properly grounded and polarized electric outlet.

Product Damage

Do not plug unit in until tank is filled with water and water flows from spout.

Do not under any circumstances use bleach, abrasive liquids, powders or scouring pads to clean the faucet as doing so could void your war- ranty. Occasional cleaning with a soft cloth and warm soapy water is sufficient.

A hot water dispenser, like any water heater, has limited life and will eventually fail. To avoid possible property damage, a hot water dispenser should be regularly examined for leakage and replaced when necessary. A drain pan plumbed to an appropriate drain is suggested in those applications where any leakage could cause property damage.

IMPORTANT WARRANTY INFORMATION!

Retain your receipts (purchase and/or installation) as these document the start date of your 1-year warranty. In the absence of purchase or installation receipts, your warranty is one full year from the date of manufacture.

Dispenser head configurations covered in this installation guide.

If your dispenser head still varies, you may require another installation guide.

4.1

5.4

4.5

6.5

These are the tools and materials you will need

Pliers

Phillips and flat blade screwdrivers

Adjustable wrench

115-volt grounded outlet

within 30 inches (76 cm) of the dispenser

Cold water line within 2 feet (61 cm ) of the dis- penser. A shutoff valve to connect the dispenser to the cold water line (see step 4 for examples of connections that can be used).

These are the tools you may need

Cordless or hand drill. If you have galvanized water supply pipe, you may need a non-elec- tric drill to make a small hole.

Basin Wrench. If you intend to use the hand sprayer hole in your sink for your dispenser, you may need a basin wrench and a 1/8" plug or a 1/4" cap for the faucet spray hose line. See item 1 of installation instructions for details.

Chassis punch. If you need to punch a mounting hole in your stainless steel sink you may need a 1-1/4" (3.2 cm) chassis punch.

		5.6
3.5	4.3
	2.5	2.5

GN/HC WATER DISPENSER H-770 WATER DISPENSER H-990 WATER DISPENSER

INSTALLATION QUESTIONS?

Call the Answerline at 1-800-558-5700

P/N 43142 Rev. 10/00