Directed Electronics HCCA-D1200 warranty CEA Specifications

Page 6

2.+BAT - connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio sys- tem battery.

WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection.

3.REM - this terminal turns on the amplifier when (+) 12 volt is applied. Connect it to the remote turn on lead of the head unit or signal source. If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/N #55000) can be used to supply a remote turn on signal. DO NOT connect this terminal to constant (+) 12 volt.

4.GND - power return connection. Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+) 12 volt power wire. The chassis connection point should be scraped free of paint and dirt. Use only quali- ty crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points.

5.Speaker - connect the speakers to these terminals. (refer to the Speaker Connection section of this guide.)

NOTE: Make all connections to power, ground, speakers, and remote terminals before final positioning and installation of the amplifier in the vehicle.

NOTE: the HCCA-D5000 has two terminal strips for power connections. The +BAT and GND connections can be made to either of these terminals.

CEA SPECIFICATIONS

HCCA-D1200

Power Output: 250 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -60 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 600 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

HCCA-D2400

Power Output: 450 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -60 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 1200 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

HCCA-D5000

Power Output: 1000 Watts RMS x 1 at 4 ohms and < 1% THD+N

Signal to Noise Ratio: -60 dBA (reference 1 Watt into 4 ohms)

Additional Power Output: 2500 Watts RMS x 1 at 1 ohm at 14.4 Supply<1% THD+N

© 2006 Directed Electronics, all rights reserved

5

Image 6
Contents Warranty Contents Introduction Important NoteWhat’s in the Box Practice Safe Sound Record Your Serial Number and DateEND Panel Layouts HCCA-D2400 CEA Specifications HCCA-D1200Specifications Amplifier Section HCCA-D1200 HCCA-D2400 HCCA-D5000Amplifier Settings Low-Pass Crossover Fine Tuning the CrossoversAdjusting INTELLi Q High-Pass CrossoverInfinite Baffle Example High-Pass Set at 30Hz Enclosure Type Boost LevelsSealed Example High-Pass Set at 20Hz Sealed Example High-Pass Set at 30HzVented Example High-Pass Set at 30Hz Power Connections for the HCCA-D5000 Amplifier WiringPower Connections for the HCCA-D1200, and HCCA-D2400 Remote Gain OperationSpeaker Connections Bridging strappingPassenger Compartment Amplifier InstallationChoosing Mounting Locations Trunk CompartmentGeneral Precautions and Installation Tips Tools of the TradeStep By Step Installation SET UP and Troubleshooting Testing the SystemAdjusting the Sound of the System Directed Electronics, all rights reserved Troubleshooting Tips Symptom Probable Cause Action To TakeInternal Crossover Configuration APPENDIX-PROGRAMMABLE Features Directed Electronics, all rights reserved Directed Electronics, all rights reserved Directed Electronics, all rights reserved