Electrolux DDO61GA manual Connecting to GAS, Connection to the Electricity Supply

Page 45

4. CONNECTING TO GAS

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE:

ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Carry out a gas tightness test after connecting to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig.3. Take into account that it must be possible to pull the appliance forward sufficiently. The hose must not get caught on the stability bracket.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS. 669 CURRENT EDITION.

50 100

850

Fig.3

700

L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50 mbar AND TO CARRY A RED STRIPE, BAND OR LABEL.

250

450

All dimensions in

mm

5. CONNECTION TO THE ELECTRICITY SUPPLY

WARNING: THIS APPLIANCE MUST BE EARTHED.

 

DO NOT EARTH THIS APPLIANCE TO THE GAS

 

SUPPLY PIPING.

Fig.4

This appliance must be connected to 230V-240V A.C.

 

50Hz supply. It is supplied with 2 metres of 5 amp 3

 

core cable incorporating a moulded 13 amp plug , fitted

 

with a 3 amp fuse, which can be plugged directly into

 

the nearest suitable socket. Ensure the plug is accessible

 

to the user. If this is not long enough,the supply cable

 

can be replaced totally by a longer cable at least 0.75mm²

 

nominal cross sectional area (24/0.2mm).

 

IF THE MOULDED PLUG IS CUT FROM THE CABLE

FOR ANY REASON, IT MUST BE DESTROYED OR

DISPOSED OF SAFELY, AS THE PROTRUDING

WIRES WILL BE AN ELECTRIC SHOCK HAZARD.

If any other type of plug is used it should incorporate a 3 amp fuse in either the plug or adapter or at the distribution board.

If the cable has to be threaded through small apertures in cabinets etc., it may be disconnected from the appliance, then re-connected to as shown in Fig.4.

DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND/OR INSULATION TAPE.

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH I.E.E. WIRING REGULATIONS.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents ModelDDO61GA Introduction For your safetyContents Hotplate Lighting the applianceGrill/second oven Leave the grill door open when you are using the grillGrill Second ovenMain oven To turn off any burnerOven light High setting Prior to using the grillGrill Heat controlGeneral Cooking positionsPreheating Positioning food on the gridGrill pan is supplied with a removable handle Grill pan and handleBurner sizes HotplateAre reaching across the hotplate Take care to avoid burns and scalds when youHelpful hints Ovens Heat zonesOven shelves Baking trays and dishes Condensation RoastingOven cooking chart Main oven Mins. per ½kg 1lb and 15 mins Mins. per ½kg 1lb and 25 mins¼ 2¾ hours 205 mm ½ 2¾ hoursRolls and buns 10 20 mins 30 40 minsBase Medium Oven cooking chart Second ovenLamb Shelf on Medium Base Well Done½ hours Individual 20 30 mins Cakes Christmas Cake Shelf ½ 4½ hoursFruit pie shortcrust 25 35 mins Pastries Plate tart shortcrust 25 35 minsBaking tray Baked custard 50 60 minsIncrease control Bell SymbolButton 1 to decrease or button 2 to See FigRead 0.00, See Fig Release button 1 and press and hold Hours and 59 minutesTime press button At the end of the time period an audible Show in the display. See figSlow cooking Food preparation slow cookingPlease note There is no slow cook on the second oven Cover food with a tight fitting lid or tinfoil Do not cook casseroles over 2.7kg 6lbThaw thoroughly before cooking Left over food should be cooled quickly and refrigeratedCleaning the handles and control knobs Care and cleaning For your safetyCap to crown When replacing hotplate burner partsGrill and top oven Main oven Main oven cleaning cycle To remove the outer glass Cleaning between the outer and inner door glassInstalling the appliance Cleaning The Door GlassLocation Make sure that a stability bracket is fittedPositioning Appliance dimensionsCurtains behind the appliance Height to hotplate 900mm 920mmGeneral information For your safety Connecting to the electricity supplyMoving your appliance Replacing the oven light bulb Check What is wrong and why?Probably a fault Name Model Number Serial Number C. Number Service and spare partsCustomer Care Department Installation Instructions Connections DimensionsGrill HotplateMain Oven Important Safety RequirementsSecond Oven GeneralLocation of Appliance Parts Required Levelling the ApplianceFitting the Stability Bracket Connection to the Electricity Supply Connecting to GASPressure Testing Checking the GrillChecking the Hotplate Checking the Main Oven Checking LID SHUT-OFF DeviceChecking the Second Oven Checking the Main Oven LightGeneral Note Minute Minder OperationStandard guarantee conditions Guarantee ConditionsO 6 1 G a Contents Check List SL1 1DZ Telephone 0870 5 Part Number311686800 55 77 High Street
Top Page Image Contents