Electrolux EIKG6049 manual Connecting to GAS Supply, Fitting the Stability Chain, Pressure Testing

Page 34

CONNECTING TO GAS SUPPLY

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R3/8. Connection is made to the Rc ½ (½” B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID

SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Carry out a gas tightness test after connecting to the gas supply. The gas bayonet connector must be fitted in the shaded area indicated in Fig.3. Take into account that it must be possible to pull the appliance forward sufficiently. Ensure the hose does not become trapped when pushing the appliance into position.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS.669 CURRENT EDITION.

LPG Flexible connections must be a type suitable for L.P.G and capable of operation up to 50 mbar and carry a red stripe, band or label.

FITTING THE STABILITY CHAIN

It is recommended that if the appliance is to be installed with a flexible supply pipe, a stability chain be fitted and is available from your supplier (see Important Safety Requirements). These instructions should be read in conjunction with any leaflet packed with the stability chain.

1.Place the appliance in its intended position and level appliance.

2.Mark a position 100mm from the top of the rear right hand corner.

3.Measure down 150mm from this point. This gives the position of the wall anchor point for the stability chain.

4.The stability chain anchor point on the appliance is shown in the diagram Fig. 4.

PRESSURE TESTING

1.The Rapid injector is used as a pressure test point.

2.Connect the pressure gauge to the Rapid injector.

3.Check the supply pressure by turning the Rapid burner on and one other hotplate burner full on and light the appropriate burner. The pressure should be either:-

(i)For Natural Gas 20mbar

(ii)For LP. Gas. The pressure must be set to 29 mbar for use on butane or 37 mbar for use on propane.

4.Turn off the taps, disconnect the pressure gauge.

5.Check operation of each hotplate burner.

34

Fig.3.

Fig.4.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model EIKG6049 Child Safety Important Safety InformationInstallation Cleaning and MaintenanceContents Description of the Appliance SLIP-IN GAS Double OvenGetting to Know Your Appliance FeaturesControl Panel Before Using the Appliance Timer HOW to SET the CountdownSetting the Oven Timer Control To Cancel the CountdownTo SET the Timer to Switch on and OFF Automatically To Return the Appliance to Manual To SET the Timer to Switch OFF onlyTo Cancel AN Automatic Programme Things to NoteTo Light the HOB Burners Using the HOBHOB To Turn OFF ANY BurnerHints and Tips Grill PAN and Handle Using the GrillGrill Ensure the handle is correctly locatedAlways remove the grill pan handle during grilling Grilling ChartMins in total Preheating Using the TOP OvenTOP Oven To FIT the TOP Oven ShelfHints and Tips Heat Zones Using the Main OvenMain Oven To FIT the Main Oven ShelvesHints and Tips Mark Cooking ChartGas Mark Cook Time minRoasting Chart MeattemperatureSlow Cook Using Slow CookFood Preparation Slow Cooking Vegetables Cleaning the Outside of the Appliance Care and CleaningCleaning Materials Cleaning the Control Knobs and HandlesWhen Replacing Hotplate Burner Parts Cleaning the HOBCleaning the Grill Cleaning Inside the Grill and Oven Compartments Aerosol cleaners must not be used on Stayclean surfacesCleaning Between the Outer and Inner Door Glass Cleaning the DoorsTo Replace the Outer Glass Replacing AN Oven Light Bulb Problem Something not WORKING?Service and Spare Parts Guarantee Conditions This guarantee does not coverDimensions Technical DetailsImportant Safety Requirements Installation InstructionsProvision for Ventilation Location of Appliance For Your SafetyMoving Your Appliance Levelling the ApplianceConnect to 230-240 A.C supply only Connecting to the Electricity SupplyIf a moulded plug is fitted Pressure Testing Connecting to GAS SupplyFitting the Stability Chain Checking LID SHUT-OFF Device Checking the GrillChecking the Hotplate Checking the Second OvenTo SET the Time of DAY Checking the Main OvenChecking the Main Oven Light General NotePage Page Page Electrolux Major Appliances Addington WAY Luton Bedfordshire
Top Page Image Contents