Electrolux 269555, 267554, 267552 manual Safety Devices, Operation Check, Servicing, Troubleshooting

Page 18

USA

7. SAFETY DEVICES

The appliance is fitted with the following safety devices:

-Fuses (see electrical circuit diagram) located behind the control panel.

To change a fuse unscrew and remove the retainer cap and replace the blown fuse with an identically rated component; the fuse rating value is specified on the relative dataplate.

-Oven chamber safety thermostat with manual reset, located behind the control panel; when this device trips, convection heating power is disconnected.

Notice: CONTACT YOUR AUTHORIZED SERVICE COMPANY TO PERFORM MANINTENANCE AND REPAIRS.

-Automatic reset thermal protection inside the cavity fan motor: this device trips in the event of overheating of the cavity fan motor; this cut-out protects the appliance by disconnecting the power supply to the main PC board and an error message is display EFUN.

8. OPERATION CHECK

-Switch on the appliance in accordance with the following section "Instructions for use".

-With the aid of the Instruction Booklet, explain operation, routine maintenance, and cleaning to the user.

Important:

-Exercise due care since certain areas of the oven exterior become hot during use.

-Do not cover the exhaust outlets on top of the appliance.

9. SERVICING

All components requiring routine maintenance may be easily reached by opening the control panel, removing the left side panel, or removing the rear panel.

Danger: Live voltage is present with panels removed and unit switch on. Exercise extreme caution when work with live voltage.

NOTICE: Using any parts other than OEM original spare parts relieves the manufacturer of all warranty and liability.

10. TROUBLESHOOTING

Malfunctions may occur even when the appliance is used correctly.

Burner fails to light (message "burn" appears on display TM , see "Instructions for use" chapter 5).

Possible causes:

-The ignition electrode is incorrectly positioned or the insulation is damaged. The optimum distance from the outside of the electrode to the boiler burner is approximately 5 mm(8mm Mod. 20 GN1/1), while the equivalent distance for the convector burner is approximately 4.5 mm.

-The ignition / flame control device is damaged.

-The ignition electrode high tension lead is broken or shorting to ground.

-Insufficient gas pressure.

-Faulty gas valve.

-Burner fan unit damaged, insufficient air pressure in combustion chamber.

-Electronic control panel is damaged.

-Blown fuse, check electrical diagram.

-Oven chamber temperature probe damaged (error EPt1 - see

"Instructions for use" chapter 5).

-Temperature limiter trip.

-High room air humidity (condensation): ventilate the kitchen.

Burner flame extinguishes (message "burn" appears on display TM, see "Instructions for use" chapter 5).

Possible causes:

-Power supply polarity (Phase/Neutral) inverted.

-Electrical supply to oven is "Phase/Phase" type. In this case fit the special "Transformer Kit" available from the manufacturer on request.

-Faulty gas valve.

-Flame detector electrode incorrectly positioned or in open circuit.

-Burner fan unit damaged (lockout situation).

-Flame control device damaged

-High room air humidity (condensation): ventilate the kitchen.

Oven chamber temperature thermostat control is incorrect. Possible causes:

-Electronic control panel faulty.

-Oven chamber temperature probe is dirty, faulty, or interrupted, see error EPt1 (see "Instructions for use" chapter 5).

Oven fails to turn on. Possible causes:

-Electronic control panel is damaged.

-Fuse F2 blown due to damaged control circuit components.

Oven chamber lamps damaged

CAUTION: Before changing oven chamber lamps switch off the appliance.

11. LAYOUT OF MAIN COMPONENTS

(All work inside the appliance must be carried out exclusively by a trained installer authorised by the manufacturer)

Removing the control panel provides access to the following components:

Danger: Live voltage is present with panels removed and unit switch on. Exercise extreme caution when work with live voltage.

-Electronic circuit boards

-Oven chamber temperature limit thermostat

-Fuses

-Door microswitch

-Oven chamber lamp transformer

-Geared motor for the oven chamber pressure relief butterfly valve.

WARNING: Before servicing unit switch off power at the main circuit breaker and place a red tag on the breaker to indicate work is being done on the circuit.

Remove the appliance left hand side panel to gain access to all the other components.

5938 036 01

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DOC. no 036 Esquema Para LA Instalación Mod GN 1/1 Niveau FonctionnelNivel Funcional Mod GN 2/1 5938 1208 mm 364 mm 335 200 5938 036 5938 Instructions for Installation and USE Appliance IdentificationMain Features Description of ApplianceTechnical Data GN 1/1 GN 2/1 10 GN 1/1 10 GN 2/1 20 GN 1/1 20 GN 2/1Precautions Keep the appliance area free and clear from combustiblesUSE Safeguarding the EnvironmentCleaning DisposalPlace of Installation PositioningCombusted GAS Discharge Installation of Accessories Always installWater Mains Connection Installing the Power Supply CableElectrical Connection Water Supply ConnectionsChecking the Supply Pressure a GAS ConnectionNominal Heat Output Waring Blocking the Drain is HazardousOperation Check Safety DevicesTroubleshooting Servicing6- and 10-GRID Models Opening the Oven DoorClosing the Oven Door 20-GRID ModelsMain Controls Description of the Control PanelIntroduction Main Cooking ModesAdditional Functions Boiler status LEDLED off boiler ready Operating Level Switching the Oven onManual Controls Setting the Cooking Cycle IntroductionSetting the Cooking Time Important do not set the cooking time on Timer TMSetting Cooking Humidity Start the cycle. Press the Cooking Start/Stop buttonOven Chamber Humidity Cooking Utilities Cooking with TWO Phases in Automatic SequenceDelta Cooking UtilityPhase 2 flashing Selected item Return to menu Select the phasesPhase 1 flashing Selected item Automatic ControlsEditing the SET Parameters Setting the TIME, Date and Delay StartProgram Selected Storing Recipes or ProgramsUsing Preset Programs Recipe or Program SearchDeleting a Recipe or Program from the Memory Information and Error CodesPassword Selected optionRinse AID Switching OFF in the Event of a FaultCare and Maintenance DetergentPeriodical Maintenance of the Boiler Descaler Cleaning MethodSpecial Cleaning Instructions Replacing Consumable Components

267553, 267552, 267550, 269550, 267554 specifications

Electrolux has long been synonymous with quality and innovation in the home appliance sector. Among its diverse lineup, the models 269552, 267555, 269551, 267551, and 269555 stand out, showcasing cutting-edge technologies and user-centric features that redefine efficiency and convenience in modern households.

The Electrolux 269552 is lauded for its ergonomic design and sophisticated functionality. This model integrates advanced ergonomic features, making it easy to operate for users of all ages. The design emphasizes user comfort, with intuitive controls and a lightweight frame that enhances maneuverability. In addition, the 269552 boasts a powerful motor that delivers superior performance, ensuring optimal cleaning results across various surfaces.

The 267555 is a standout model focused on energy efficiency and sustainability. With its eco-friendly technology, this model not only minimizes energy consumption but also reduces the environmental footprint. The 267555 features smart sensors that automatically adjust power based on the surface being cleaned, further optimizing energy usage without sacrificing cleaning performance. This model is perfect for environmentally conscious consumers looking for efficiency without compromising on effectiveness.

The Electrolux 269551 and 267551 models share similar DNA but cater to different needs. The 269551 is engineered for heavy-duty cleaning tasks, equipped with high-capacity dust containers and washable filters that improve airflow and maintain suction power over time. Meanwhile, the 267551 offers versatile cleaning options with detachable components for transitioning between various tasks effortlessly.

Lastly, the Electrolux 269555 combines functionality with style. This model comes with a sleek, modern design that complements any home decor, while featuring cutting-edge technology such as smart cleaning modes and app connectivity. Users can control the 269555 from their smartphones, setting schedules and customizing cleaning preferences for maximum convenience.

Together, these Electrolux models offer a blend of performance, innovation, and sustainability. With their unique features and technologies, they represent the brand's commitment to quality and consumer satisfaction, making them ideal choices for anyone looking to enhance their home cleaning experience. Whether you prioritize energy efficiency, design, or heavy-duty capabilities, Electrolux has a model tailored to your needs.
Top Page Image Contents