Electrolux PL36WC50EC manual Operation, Halogen Bulbs, Maintenance

Page 3

OPERATION

Controls

The hood is operated using the (4) push-buttons located at eye-level, on the front edge of the hood.

The light switch turns the halogen lamps on and off.

The blower on-low / off switch turns the blower on to its lowest running speed. The blower must be turned on using this switch. Turn the blower off by pressing this switch a second time.

The blower medium speed switch changes the blower speed to medium. This switch works only if the blower is already running at low or high speed.

The blower high speed switch changes the blower speed to high. This switch works only if the blower is already running at low or medium speed.

The pilot lamp lights up whenever the blower is on.

LIGHT

 

BLOWER

 

MEDIUM

 

PILOT

SWITCH

 

SPEED

 

LAMP

 

 

BLOWER

 

BLOWER

 

 

ON-LOW /

 

 

 

 

HIGH

 

 

 

OFF

 

 

 

 

 

SPEED

 

 

 

SWITCH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. 1

HALOGEN BULBS

This range hood requires two halogen bulbs (Type GU10, MR16 shielded, 120V, 50W).

ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CARRYING OUT

ANY OPERATIONS ON THE APPLIANCE.

1.Loosen the ring nut by turning it counterclockwise.

2.Loosen the bulb by turning it counterclockwise; pull the bulb downwards to remove. CAUTION: BULB MAY BE HOT!

3. Replace with Type GU10, MR16 shielded, 120V, 50W halogen bulb.

BULB

 

 

RING NUT

 

 

 

 

 

FIG. 2

MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Grease Filters

The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe.

See “INSTALL FILTERS” section for removal and installation instructions.

Non-Ducted Recirculation Filter

The non-ducted recirculation filter should be changed every 6 months.

See “INSTALL FILTERS” section for removal and installation instructions.

Hood Cleaning

Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips:

Hot water with soap or detergent is all that is usually needed.

Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks.

For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth.

For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub lightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface.

DO NOT allow deposits to remain for long periods of time.

DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust.

DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.

Painted surfaces should be cleaned with warm water and mild detergent only.

- 4 -

Image 3
Contents Model PL36WC50EC Intended for Domestic Cooking only Read and Save These InstructionsMaintenance OperationHalogen Bulbs Prepare the Hood Ducted Hoods only Install the DuctworkInstall Electrical Install Mounting BracketInstall Flue Mounting Bracket NON Ducted Hoods only Install the HoodInstall Decorative Flues Make Electrical ConnectionsRooms with 10-FOOT Ceilings Ducted Hoods only NON-DUCTED Hoods only Install FiltersMajor Appliance Warranty Information Models PL36WC50EC Service Parts Liste Pieces DE RechangeModel PL36WC50EC