Electrolux AOS061E manual Special Cleaning Instructions, Replacing Consumable Components

Page 32

USA

IMPORTANT - 1

Insert a rubber hose inside the boiler filler pipe and rinse thoroughly with water to remove all traces of descaling agent.

•Refit the filler plug and close the boiler drain (by pressing the relative button).

After descaling the boiler, it is good practice to execute a 30- minute STEAM cycle with the oven empty.

IMPORTANT - 2

If the water supply cock cannot be easily accessed, to empty the boiler proceed as follows:

1)Open the boiler discharge valve with the special pushbutton.

2)Wait 2 minutes and switch the oven off; the discharge valve will close automatically.

7.3 SPECIAL CLEANING INSTRUCTIONS

Cleaning and checking the drain system

Periodically clean the drain pipe and check for obstructions that may prevent the water from draining.

Cleaning the oven door glazing panels (Fig. 5)

Only clean the panels when the glass is cool and never use abrasive cloths or detergents.

To access the double glazing cavity, open the internal panel, which is hinged to the door.

•Open the oven door and press both upper and lower clips F to release the internal glazing panel.

7.2 REPLACING CONSUMABLE COMPONENTS

Changing the oven chamber lamp (Fig. 3)

If the oven chamber lamp burns out, replace as follows:

•Disconnect the appliance from the power supply.

•Unscrew the four screws fixing flange "A" and remove glass shield "V" together with seal "G".

•Remove halogen lamp "L" and fit an equivalent lamp with identical characteristics (12V - 20W - 572°F). Important: do not touch the new lamp with your fingers, wrap it in paper or a clean cloth when fitting.

•Refit the glass shield with the seal in the lamp recess then smear food grade silicone grease on the seal and secure the flange using

the four screws.

3

Replacing the oven door seal (Fig. 4)

N.B.: The oven door seal is prone to normal wear and aging and should be replaced whenever it starts to harden or crack.

To change the oven door seal proceed as follows:

•prise the seal out of its seat and remove all traces of old silicone from the channel.

•apply a bead of silicone sealant in point 1 along the internal frame of the seal seating channel.

•insert the new seal, pressing it home along the entire length of the channel.

5

After cleaning close the internal panel ensuring it is properly seated against the rubber stops.

CLEANING SYSTEM rotary spray arm (Fig. 6) Clean the spray arm in the following cases:

-prolonged disuse of the CLEANING SYSTEM

-faulty rotation of the spray arm (nozzles probably blocked)

-use of the appliance with very hard water.

If the nozzles are completely blocked, remove scale deposits using the tip of a knife.

•Disengage (without removing) spring clip A from the central block of the spray arm. For this operation, insert the tip of a screwdriver in the position shown by the arrow and turn it from the vertical to the horizontal position as shown in the figure.

•Remove the spray arm from its hub.

6

 

• Place the spray arm in a bowl full of descaling agent and leave

 

it to soak overnight, rinsing thoroughly before refitting.

4

• Refit the spray arm by inserting it over the hub and returning the

spring clip to its original position.

 

5938 036 01

32

Page 31 Page 32
Image 32
Page 31 Page 32
Contents DOC. no 036 Esquema Para LA Instalación Nivel Funcional Mod GN 1/1Niveau Fonctionnel Mod GN 2/1 5938 1208 mm 364 mm 335 200 5938 036 5938 Instructions for Installation and USE Appliance IdentificationMain Features Description of ApplianceTechnical Data GN 1/1 GN 2/1 10 GN 1/1 10 GN 2/1 20 GN 1/1 20 GN 2/1Precautions Keep the appliance area free and clear from combustiblesSafeguarding the Environment CleaningUSE DisposalCombusted GAS Discharge Place of InstallationPositioning Installation of Accessories Always installInstalling the Power Supply Cable Electrical ConnectionWater Mains Connection Water Supply ConnectionsGAS Connection Nominal Heat OutputChecking the Supply Pressure a Waring Blocking the Drain is HazardousSafety Devices TroubleshootingOperation Check ServicingOpening the Oven Door Closing the Oven Door6- and 10-GRID Models 20-GRID ModelsDescription of the Control Panel IntroductionMain Controls Main Cooking ModesLED off boiler ready Additional FunctionsBoiler status LED Switching the Oven on Manual Controls Setting the Cooking CycleOperating Level IntroductionSetting the Cooking Time Important do not set the cooking time on Timer TMOven Chamber Humidity Cooking Setting Cooking HumidityStart the cycle. Press the Cooking Start/Stop button Cooking with TWO Phases in Automatic Sequence Delta CookingUtilities UtilityReturn to menu Select the phases Phase 1 flashing Selected itemPhase 2 flashing Selected item Automatic ControlsSetting the TIME, Date and Delay Start Program SelectedEditing the SET Parameters Storing Recipes or ProgramsUsing Preset Programs Recipe or Program SearchInformation and Error Codes PasswordDeleting a Recipe or Program from the Memory Selected optionSwitching OFF in the Event of a Fault Care and MaintenanceRinse AID DetergentPeriodical Maintenance of the Boiler Descaler Cleaning MethodSpecial Cleaning Instructions Replacing Consumable Components

AOS061E specifications

The Electrolux AOS061E is a versatile and efficient air conditioning unit designed to enhance indoor comfort while maximizing energy savings. This model is particularly appealing for individuals and families seeking a reliable cooling solution that seamlessly integrates into their living environment.

One of the standout features of the AOS061E is its energy efficiency. The unit operates with a high Energy Efficiency Ratio (EER), indicating that it effectively transforms electrical energy into cooling power. This not only helps in reducing electricity bills but also highlights its commitment to eco-friendliness, making it a commendable choice for environmentally conscious consumers.

The AOS061E incorporates advanced inverter technology, which allows for precise temperature control and quieter operation. The inverter system adjusts the compressor's speed according to the cooling demand, ensuring that the space is maintained at the desired temperature without unnecessary power consumption. This results in a more stable and comfortable climate, particularly during extreme weather conditions.

Another key characteristic of the Electrolux AOS061E is its user-friendly interface. Equipped with an intuitive remote control, users can easily adjust settings from anywhere in the room. The unit also includes a digital display that provides real-time information about the temperature and chosen modes. Additionally, several cooling modes, such as turbo and sleep mode, are available to cater to different preferences and needs.

The AOS061E features a sleek and modern design, ensuring it complements various interior styles. Its compact size allows for easy installation in a myriad of settings, whether in small apartments, offices, or larger living spaces. The unit is also equipped with a washable air filter, promoting better air quality by capturing dust and allergens, which is vital for households with allergy sufferers.

In terms of noise levels, the AOS061E operates quietly, making it suitable for use in bedrooms, study areas, or any other location where sound might be a concern. The low decibel output allows for uninterrupted sleep and concentration.

Overall, the Electrolux AOS061E is a feature-packed air conditioning unit that prioritizes efficiency, comfort, and convenience. Its blend of advanced technology, user-friendly controls, and sleek design make it an excellent choice for anyone looking to improve their indoor climate while being mindful of energy consumption. With the AOS061E, achieving optimal comfort at home is not only possible but also effortless.
Top Page Image Contents