Electrolux 137519000 A (1112) manual Avoid Service Checklist, Water

Page 26

26Solutions to Common Problems

Avoid Service Checklist, continued

OCCURRENCE

POSSIBLE CAUSE

SOLUTION

WATER

 

 

Water collects in folds of

This is a result of the washing action and

 

the bellows at the end of

is part of the normal operation of the

 

the cycle.

washer.

 

 

 

 

Water collects in bleach

This is a result of the siphoning action

Water may be removed by removing the dispenser

and fabric softener com-

and is part of the normal operation of the

drawer (see Care and Cleaning in this guide) and draining

partments.

washer.

water into the empty drum or sink.

 

 

 

Wash load too wet after

Washer is overloaded.

Do not overload washer. See Operating Your Washer,

spin.

 

step 4.

 

 

 

 

Load is too small.

Add 1 or 2 similar items to help balance the load.

 

 

 

 

Load is out of balance.

Rearrange load to allow proper spinning.

 

 

 

 

Drain hose is kinked.

Straighten drain hose.

 

 

 

Water does not enter

Water supply is not adequate in area.

Check another faucet in the house. Wait until water supply

washer or it enters slowly.

 

and pressure increase.

 

 

 

 

Water supply faucets are not completely

Fully open hot and cold faucets.

 

open.

 

 

 

 

Water is being used elsewhere in the house. Water pressure must be at least 30 psi (260 kPa).

Avoid running water elsewhere while washer is filling.

Water inlet hoses are kinked.

Straighten hoses.

Warm or hot water is not hot enough.

Hot water heater is set too low or is a distance from washer.

Measure hot water temperature at nearby faucet with candy or meat thermometer. Water temperature should be at least 120°F (49°C). Adjust water heater as neces- sary.

Hot water is being used elsewhere in the house.

Avoid using hot water elsewhere before or during washer use. There may not be enough hot water avail- able for proper cleaning. If problem persists, your hot water system may be unable to support more than 1 use at a time.

Water in washer does not

Drain hose is kinked or clogged.

Clean and straighten the drain hose.

drain or drains slowly.

 

 

Drain hose standpipe is too tall. Maxi-

Reduce standpipe height to less than 8’ (2.4 m). See

 

 

mum standpipe height is 8’ (2.4 m).

INSTALLATION INSTRUCTIONS.

 

 

 

 

House drain pipes are clogged.

Unclog drain pipes. Contact plumber if necessary.

 

 

 

Water leaks.

Fill hose connection is loose at faucet or

Check and tighten hose connections. Install rubber

 

washer.

sealing washers provided.

 

 

 

Oversudsing.

Wrong detergent.

Run rinse cycle. Use a low-sudsing, high efficiency

 

 

detergent.

 

 

 

 

Too much detergent.

Run rinse cycle. Use less detergent in future loads.

 

 

 

Incorrect wash and rinse

Hot and cold water hoses are connected

Connect hot water hose to hot water faucet and cold

temperatures.

to wrong supply faucets.

water hose to cold water faucet.

 

 

 

Water is entering washer

Drain hose standpipe is too low. Stand-

Increase standpipe height to at least 23.6” (60 cm). See

but tub does not fill.

pipe must be a minimum of 23.6” (60 cm)

INSTALLATION INSTRUCTIONS.

 

high to prevent siphoning.

 

 

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Use & Care Guide Please read and save this guide Table of contentsFinding Information Keep a record for quick referenceRecognize safety symbols, words and labels SafetyImportant Safety Instructions Prevent FirePrevent Injury Prevent Injury and Damage to the WasherFeatures Operating Your Washer Operating InstructionsNormal Operating Sounds Pretreat stains and heavy soil Sort laundry into loads that can be washed togetherPrepare items for washing Add laundry load to washerLiquid Detergent Powder DetergentDetergent for Prewash Operating Your WasherOther Wash Products Liquid Chlorine BleachStart the washer Entrapment and TIP-OVER HazardCycle Selection Cycle Selection My Favorite Cycle Spin Speed Cycle SettingsWashing Temperature Soil LevelCycle Options Other Features Washer Settings Chart Stain Removal Procedures Stain Removal GuideStain Removal Suggestions Stain TreatmentTo Refresh or Clean Inside of Washer Care & CleaningInside Routine Cleaning Preventive Other Inside Routine Cleaning Preventive Cleaning Dispenser Drawer AreaInside Cleaning Aggressive Cleaning Procedure Washer DrumOutside Routine Cleaning Winterizing InstructionsSolutions to Common Problems Common Washing ProblemsDo not use chlorine bleach to re Service Prevention Checklist Occurrence Possible Cause SolutionAvoid Service Checklist WaterWarranty Information Warranty Periods

137519000 A (1112) specifications

The Electrolux 137519000 A (1112) is a reliable and versatile appliance designed to meet the demands of modern households. This model stands out for its combination of innovative technologies, user-friendly features, and distinctive design, making it a preferred choice for many consumers.

One of the main features of the Electrolux 137519000 A (1112) is its energy efficiency. This appliance is engineered to operate with minimal energy consumption while maintaining high performance, which not only helps to reduce electricity bills but also minimizes environmental impact. It is built with energy-saving components that are compliant with current energy standards, ensuring that it meets or exceeds user expectations for sustainability.

In terms of technology, the Electrolux 137519000 A (1112) integrates advanced functions designed to enhance the user experience. The intuitive control panel allows users to easily navigate through various settings and options, making operation smooth and straightforward. The appliance may also include smart technology features, enabling connectivity with mobile devices for remote monitoring and control. This is particularly beneficial for multitasking individuals who wish to manage their home appliances conveniently.

Safety is another critical aspect of the Electrolux 137519000 A (1112). This model includes features such as automatic shut-off systems and heat-resistant materials to ensure the safety of the appliance during use. Additionally, it provides clear safety instructions to guide users, alleviating concerns and enhancing the overall user experience.

The design of the Electrolux 137519000 A (1112) is as practical as its performance. With a sleek and modern aesthetic, it can seamlessly blend into various kitchen styles, adding an element of sophistication. The materials used are not only sturdy but also easy to clean, promoting a tidy and hygienic environment.

Overall, the Electrolux 137519000 A (1112) is a well-rounded appliance that offers energy efficiency, modern technology, and aesthetic appeal. It is a testament to Electrolux's commitment to quality and innovation. Whether you are looking to upgrade your kitchen or simply seeking a reliable appliance, the Electrolux 137519000 A (1112) promises to deliver exceptional performance and satisfaction.
Top Page Image Contents