Electrolux 349095801 manual Installation Instructions

Page 31

INSTALLATION INSTRUCTIONS

WARNING: THIS APPLIANCE MUST BE EARTHED

If your appliance has been damaged in transit, contact your supplier immediately. Do not attempt to install it.

Your appliance left the factory fully packaged to protect it from damage. If it is delivered without packaging and damage has occurred, the manufacturer cannot accept responsibility. Contact your supplier for advice.

Once the packaging has been removed the appliance should only be moved by hand. Do not use a sack barrow or any other aid to lift the appliance as damage may occur.

Connection to the electricity supply must be carried out by a qualified electrician/competent person.

The electrical connection should be made using a double pole isolating switch (cooker socket) with at least 3mm contact separation in all poles. The cable must have conductors of sufficiently high cross- sectional area to prevent overheating and deterioration.

The recommended cross-section area is six square millimetres (6.00mm2).

When refitting the mains terminal cover, ensure that the lower tabs are located inside the bottom edge of the aperture, before fixing the two screws into the top edge of the mains terminal cover. See Fig.1. Ensure that the cover is securely fastened.

To move the appliance, open the oven door, and lift the appliance by holding inside the top of the compartment. See Fig.2.

This is a type Y appliance, which means it is free- standing and can be fitted with cabinets on one or both sides. It may also be fitted in a corner setting.

Side walls which are above hob level should be protected by heat resistant non-combustible material and MUST NOT be nearer than 40mm to the hob side.

A nominal air gap of 2mm at either side of the appliance is required to enable the appliance to be moved into position.

Always ensure an air gap is maintained at hotplate level. Tiles or other forms of deep wall covering should not obscure this gap. See Fig.3.

Overhanging surfaces or a cooker hood should be a minimum of 685mm above the hob. See Fig.4.

It is important to ensure that the appliance is level after installation. Levelling feet are fitted to the appliance to accommodate uneven floors.

31

Fig.1.

Fig.2.

Air gap

Fig.3.

Fig.4.

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model EKC6046 /EKC6047 Installation Important Safety InformationContents SLIP-IN Electric Double Oven Description of the ApplianceCDE F G H FeaturesGetting to Know Your Appliance Control PanelBefore Using the Appliance HOW to SET the Time of DAY TimerHOW to SET the Countdown Setting the Oven Timer Control To Cancel the CountdownTo SET the Timer to Switch on and OFF Automatically Things to Note To SET the Timer to Switch OFF onlyTo Cancel AN Automatic Programme To Return the Appliance to ManualCeramic HOB Using the HOBRecommended Saucepans Hints and Tips HOT HOB IndicatorEnsure the handle is correctly located Using the GrillGrill Grill PAN and HandleGrill Time Grilling ChartFood PositionTOP Oven Using the TOP OvenTo FIT the TOP Oven Shelf Hints and Tips Main Oven Using the Main OvenTo FIT the Main Oven Shelves Hints and Tips Oven Cooking Chart Meattemperature Roasting ChartUsing Defrost Feature Defrost FeatureCleaning the Control Knobs and Handles Care and CleaningCleaning Materials Cleaning the Outside of the ApplianceTo Remove Burnt on Soilage Cleaning the Ceramic HOBDaily Cleaning To Remove More Stubborn MarksAny of the above products may cause damage to the hob To Reduce HOB SoilageAerosol cleaners must not be used on Stayclean surfaces Cleaning Inside the Grill and Oven CompartmentsTo Replace the Outer Glass Cleaning the DoorsCleaning Between the Outer and Inner Door Glass To Remove the Outer GlassReplacing AN Oven Light Bulb Oven fan is noisy Oven temperature is too high or too low Grill, ovens and timer do not workSomething not WORKING? Service and Spare Parts This guarantee does not cover Guarantee ConditionsTechnical Details Installation Instructions Important Notice
Top Page Image Contents