Electrolux EKM6045 Connecting to GAS Supply, Fitting the Stability Chain, Pressure Testing

Page 33

CONNECTING TO GAS SUPPLY

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R3/8. Connection is made to the Rc ½ (½” B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID

SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Carry out a gas tightness test after connecting to the gas supply. The gas bayonet connector must be fitted in the shaded area indicated in Fg.3. Take into account that it must be possible to pull the appliance forward sufficiently. Ensure the hose does not become trapped when pushing the appliance into position.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS.669 CURRENT EDITION.

LPG Flexible connections must be a type suitable for L.P.G and capable of operation up to 50 mbar and carry a red stripe, band or label.

FITTING THE STABILITY CHAIN

It is recommended that if the appliance is to be installed with a flexible supply pipe, a stability chain be fitted and is available from your supplier (see Important Safety Requirements). These instructions should be read in conjunction with any leaflet packed with the stability chain.

1.Place the appliance in its intended position and level appliance.

2.Mark a position 100mm from the top of the rear right hand corner.

3.Measure down 150mm from this point. This gives the position of the wall anchor point for the stability chain.

4.The stability chain anchor point on the appliance is shown in the diagram Fig. 4.

PRESSURE TESTING

1.The Rapid injector is used as a pressure test point.

2.Connect the pressure gauge to the Rapid injector.

3.Check the supply pressure by turning the Rapid burner on and one other hotplate burner full on and light the appropriate burner. The pressure should be either:-

(i)For Natural Gas 20mbar

(ii)For LP. Gas. The pressure must be set to 29 mbar for use on butane or 37 mbar for use on propane.

4.Turn off the taps, disconnect the pressure gauge.

5.Check operation of each hotplate burner.

33

Fig.3.

Fig.4.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model EKM6044 / EKM6045 Installation Important Safety InformationChild Safety Cleaning and MaintenanceContents SLIP-IN Electric Double Oven with GAS HOB Description of the ApplianceGetting to Know Your Appliance Control Panel FeaturesBefore Using the Appliance Timer HOW to SET the Time of DAYHOW to SET the Countdown To Cancel the Countdown Setting the Oven Timer ControlTo SET the Timer to Switch on and OFF Automatically To Cancel AN Automatic Programme To SET the Timer to Switch OFF onlyTo Return the Appliance to Manual Things to NoteGAS HOB Using the HOBTo Light the HOB Burners To Turn OFF ANY BurnerHints and Tips Grill Using the GrillGrill PAN and Handle Ensure the handle is correctly locatedFood Grilling ChartPosition Grill TimeUsing the TOP Oven TOP OvenTo FIT the TOP Oven Shelf Hints and Tips Using the Main Oven Main OvenTo FIT the Main Oven Shelves Hints and Tips FAN Oven TOP Oven Food Position Cooking Approx Temp C Tempc Oven Cooking ChartMeattemperature Roasting ChartUsing Defrost Feature Defrost FeatureCleaning Materials Care and CleaningCleaning the Outside of the Appliance Cleaning the Control Knobs and HandlesWhen Replacing Hotplate Burner Parts Cleaning the HOBAerosol cleaners must not be used on Stayclean surfaces Cleaning Inside the Grill and Oven CompartmentsCleaning Between the Outer and Inner Door Glass Cleaning the DoorsTo Remove the Outer Glass To Replace the Outer GlassReplacing AN Oven Light Bulb Problem Possible SolutionSomething not WORKING? Service and Spare Parts This guarantee does not cover Guarantee ConditionsTechnical Details DimensionsConnections GeneralInstallation Instructions Important Safety RequirementsProvision for Ventilation Moving Your Appliance For Your SafetyLocation of Appliance Levelling the ApplianceConnecting to the Electricity Supply Connect to 230 240V AC supply onlyEnsure That the Links are Fitted AS Shown Connecting to GAS Supply Pressure TestingFitting the Stability Chain Checking the Hotplate Checking the GrillChecking LID SHUT-OFF Device Checking the TOP OvenPage Important Notice
Top Page Image Contents