Cuisinart BFP-703C manual Food Processor Assembly for Slicing and Shredding, Operating Controls

the work bowl, turn chopping blade hub slightly and replace cover.

5.The food pusher fits in feed tube with more rounded side towards the outside of the bowl. ALWAYS

USE PUSHER TO GUIDE FOOD THROUGH FEED TUBE. NEVER USE YOUR FINGERS OR SPATULA.

6.Plug your SmartPower Duet® into a wall outlet. Push the On button and then the Food Processor button to start chopping or puréeing. It is recommended that one hand be placed on the Food Processor lid while in use for unit stability. If the machine doesn’t start, make sure it is plugged in and the work bowl and cover are locked into place. The food processor will not start until the collar, work bowl and work bowl lid are locked into place. Nevertheless, always unplug the unit before placing hands into the food processor bowl. NOTE: The motor base will start, but the food processor blade will not turn until assembled properly.

SLICING AND SHREDDING WITH THE REVERSIBLE SLICING/SHREDDING DISC

The slicing/shredding disc can slice and shred a variety of fruits and vegetables, meats and cheeses.

Food Processor Assembly for Slicing and Shredding

1.Hold collar in one hand and bowl handle in the other. Twist bowl clockwise onto collar.

2.Place collar with bowl onto motor base with handle facing front.

3.Place adapter stem onto the center shaft. To Slice: Attach disc to stem with the raised edge of slicer on top. To shred: Attach disc to stem with the raised shredding slots on top. Place the slicing/shredding disc onto shaft with the desired cutting blade facing up. Be sure

to handle the metal blade with care, as it is razor sharp.

4.Place cover on work bowl, with feed tube at about 11 o’clock. Turn cover clockwise until it fits into position. Insert food in feed tube.

5.Hold pusher with more rounded side towards the outside of the bowl and insert it in feed tube over food. Always use pusher to guide food through feed tube. Never use your fingers or spatula.

6.Plug your Cuisinart® SmartPower Duet® into a household electrical outlet.

7.To remove cover, unlock it by turning it counterclockwise, then lift it straight up.

OPERATING CONTROLS

Your SmartPower Duet™ appliance comes with a Food Processor button. This button is the perfect speed for all your food processing tasks. Always use this speed when using the food processor. You may also use the Pulse button with this function for pulse- chopping.

To use your food processor, make sure that the bowl is assembled properly and the blade or slicing/shredding disc and the cover are locked into place.

When using the control panel, the LED will light next to each button you press.

Press the On button. For continuous operation, press the Food Processor button. Motor will start if you have followed assembly instructions.

Stir						Ice	Pulse
						Crush
Chop						On	Food
							Processor
		Mix					Purée
▲						Off	S.
!	RNIN						BLAD
	WA						E
		G: F	LAS				CH
				HIN			TOU
					G LI		ON
						GHT INDICATES R EAD YTO OPERATE.D

To turn motor off, press the Food Processor button again or Off button.

For on-off operation, called pulse- chopping or pulsing, press the On button, press the Pulse button, and then press and release the Food Processor button the desired number of times. Motor runs as long as you hold the Food Processor button down. Motor stops when you release control switch. Try it a few times.

You control the duration and frequency of pulses by the length of time you hold the Food Processor button down and the rate at which you press it. Allow enough time between pulses to let food in work bowl fall to bottom.

Always use the button for pulse/chopping. Never turn cover back and forth to start and stop processor.

USING THE SMARTPOWER DUET® BLENDER/FOOD PROCESSOR TO CHOP, PURÉE, AND MIX

Refer to Food Processor Assembly instructions on page 6.

1.Remove cover and put food into work bowl.

First, cut food into 3/4"(1.9cm) pieces. You will get a more even chop if you start with pieces that are all the same size.

Put pieces into work bowl with metal blade in place. You can put in up to

1 cup of food at a time. If you want to process more, do it in batches.

2.Put on cover and lock it. Insert pusher. It is recommended that one hand be placed on the food processor lid while in use for unit stability. Press the On button, press the Pulse button, and the Food Processor button (to pulse), then release. Repeat two to three times. Each time blade stops, let food pieces drop to the bottom of bowl before pulsing again. This ensures that the blade will chop them at every pulse.

Watch what happens to the food. With pulse/chopping technique, you can get an even chop without danger of overprocessing. Check texture by looking through work bowl. Be careful not to overprocess.

For a coarse chop, pulse only a few times.

3.If you want a finer chop or purée, press the On button and then the Food Processor button and let machine run continuously until the food is chopped as fine as you want it. Check frequently through clear cover or bowl to avoid chopping

7