Viking F20725A manual Custom Wood Frame Installation Instructions Dfur Model

Page 5

Custom Wood Frame Installation Instructions (DFUR Model)

Note: Weight of wood panel must not exceed 20 lbs.

Custom Wood Frame Installation Instructions (DFUR Model) (cont.)

Step 1: Verify door alignment

The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure. (See Figure 1 below).

Top hinge pin - Remove to remove the door

 

W

 

 

 

1-23/32”

H

 

(38.8 cm)

Front of

Typical 4

 

Sides

 

overlay

Model

W

H

15”

14-5/16”

30-5/16”

(36.4 cm)

(76.9 cm)

 

24”

23-7/16”

30-5/16”

(59.5 cm)

(76.9 cm)

 

Door must be parallel to top and sides of refrigerator

Hinge adaptor screws - Loosen these to adjust door, on the top and bottom of the door

9/32”

panel

Figure 2

Glass Door Models

Table A

Glass Door Models

(7 mm)

Step 5: Clamp panel to door

Set the overlay panel on the door front, align the edges, and clamp together. Clamp the panel firmly but be careful not to crush the foam in the door or scratch the door.

Step 6: Drill holes in overlay panel

Remove the hinge adapter bushings from the top and bottom door hinge adapters. (See Figure 4). Using the holes in the hinge adapters drill 5/16” (8 mm) diameter clearance holes into the overlay panels 3/4” (20 mm) deep. These will be clearance holes for the top and bottom hinge pins.

Also, at this time, drill the screw pilot holes for attaching the overlay panel to the door. Select the size of the hole from Table B. Be careful not to drill the pilot holes through the overlay panel but only 1/2” (12.7 mm) deep.

Figure 1

Step 2: Remove door

Remove the top hinge pin from the hinge with an 1/8” allen wrench. Remove the door by angling the top of the door outward and lifting the door off the bottom hinge. (See detail in Figure 1).

Step 3: Remove gasket

Lay the door on its front being careful not to scratch it. Remove the door gasket by peeling up and out of the channel.

Step 4: Cut overlay panel

Depending on the refrigerator model cut the overlay panel to the dimensions shown. Use Figure 2 and Table A.

Note: For the door closer to work properly, it is necessary to maintain a minimum space of 9/32” (7mm) between the door and cabinet flange as shown. This space can be adjusted by adjusting the top and bottom hinge adapters.

Material Type

#8 Wood Screw

Hardwood

3/32” (2.4 mm) Diameter. Pilot Hole

Softwood

5/64” (2.0 mm) Diameter. Pilot Hole

Table B

8

9

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Viking Use/Installation Guide Important Please Read and Follow For Your SafetyProper Disposal of Your OLD Refrigeration Product General InformationSPECIFICATIONS/DIMENSIONS Designer 15 W. Models SPECIFICATIONS/DIMENSIONSFront View Professional 15 W. ModelsDesigner 24 W. Models Professional 24 W. ModelsModel Custom Wood Frame Installation Instructions Dfur ModelRight Hand Hinges shown Electrical Connection LEG Leveler InstallationEnergy Saving Tips Final PreparationGlass Door Models Setting the ControlsSolid Door Models Cleaning and Maintenance Settingthe Controls cont’dTroubleshooting Chart Wine ShelvesTruProtect Advanced Function Quick Reference Service DiagnosticsUnits certified for Outdoor Use Service InformationUnits certifiedfor Indoor Use TWO Year Full Warranty

F20725A specifications

The Viking F20725A is a remarkable model in the lineup of Viking's advanced kitchen appliances, specifically designed for culinary enthusiasts who demand premium performance coupled with innovative technology. Built with high standards of craftsmanship, the F20725A embodies the spirit of Viking's commitment to delivering professional-grade products for home chefs.

One of the standout features of the Viking F20725A is its powerful oven system. The appliance boasts a robust dual-fuel configuration, combining the precision of gas cooking with the consistent, even heating of an electric oven. This dual-fuel capability allows users to achieve exceptional cooking results, whether they're roasting, baking, or broiling. With a generous oven capacity, the F20725A provides ample space for multiple dishes, making it ideal for large family gatherings or entertaining.

The cooktop of the F20725A features six sealed burners, each designed for optimal heat distribution and control. These burners offer a variety of heat outputs, including a high-BTU burner for rapid boiling and a simmer burner for gently melting chocolate or preparing delicate sauces. The stainless-steel surface is not only aesthetically appealing but also easy to clean, ensuring a polished look in any kitchen.

Another key characteristic of the Viking F20725A is its advanced temperature management technology. The oven is equipped with a powerful convection system that uses a fan to circulate hot air throughout the cooking chamber. This ensures even baking and roasting, which minimizes hot spots and maximizes flavor development. Furthermore, the intuitive controls provide precise temperature adjustments, allowing for complete control over the cooking process.

The Viking F20725A is designed with durability in mind. It features heavy-duty construction, including a commercial-grade stainless-steel exterior and with premium quality knobs and handles designed to withstand the rigors of daily use. The appliance also integrates safety features such as automatic re-ignition and a safety lock, providing peace of mind while cooking.

Overall, the Viking F20725A exemplifies the perfect blend of style, functionality, and advanced technology. With its professional-grade features and innovative design, it serves as an invaluable asset in any modern kitchen, empowering chefs to elevate their culinary creations to new heights.
Top Page Image Contents