KitchenAid 2000495 Recommended grounrling method, Use only 114 copper tubing for water line

Page 7

Electrical requirements

Electrical Shock Hazard

l Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service technician If you are in doubt as to whether the appliance is properly grounded.

lDo Not use an extension cord with this appliance. Such use may result in a fire, electrical shock, or other personal injury.

A 120-volt, 60-Hz, AC only, 15or-20 ampere, fused, electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

Recommended grounrling method

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUNDING PRONG.

For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must,be plugged into a mating 3-prong, grounding-type wall -receptacle, grounded in accordance with the National Electrical Code, ANSI/NFPA 70-latest edition, and local codes and ordinances. See Figure 1. If a mating wall receptacle is not available. it is the personal responsibility and obligation of the customer to have a properly grounded, 3-prong wall receptacle installed by a qualified electrician.

Water supply requirements

Use only 114” copper tubing for water line.

The water line to the refrigerator must provide 15-l 00 psi water pressure.

The preferred method of installing the plumbing to the refrigerator is through the wall. An optional method is installing the water line through a floor opening. If the copper tubing is installed through the floor, the hole cut in the floor must be angled 45Otoward the front.

You will need enough l/4”- copper tubing to connect from water line to refrigerator, a saddle-type valve and a union. Rough in the water line before installing the refrigerator. See steps that follow.

Product/Property

Damage

Do Not install copper tubing in an area where temperatures drop below freezing.

To do so may result in water damage.

1 -Find a 3/8” to 1” vertical cold water line near the refrigerator. Measure the distance from the cold water line to the refrigerator location. Add 24 inches for the final length of

copper tubing you will need. Cut both ends of copper tubing square.

2.Turn off main water supply and clear water line.

Electric

Shock

Hazard.

 

Electric drill must be grounded

 

to prevent severe or lethal

 

shock if waler is in line and

 

enters

drill

during

use.

 

Failure to ground drill may

 

result

in personal

injury.

I

 

 

 

 

3.Ground electric drill or use a hand drill. Drill-a 3/16” hole in vertical cold water line. Attach a saddle valve to the water line with a clamp in an easily accessible location. Inset-l a washer between clamp and line. Check that inlet end is solidly in the drill hole. Tighten packing nut.

Tighten the pipe clamp screws evenly so washer makes a water-light connection. Do Not overtighten or copper tubing could be crushed.

4.Slide compression nut and sleeve on copper tubing. Inset-l end of Copper tubing completely into the outlet valve. Tighten compres- sion nut to outlet with an adjust- able wrench. Do Not overlighten.

Product Damage

Flush at least 2 qts. of water through the copper tubing and into a bucket before attaching to the refrigerator to get rid of any particles In water Ilne. Check for water leaks around the saddle valve.

Failure to do so may result In product damage.

5.Run water through water line, valve and copper tubing into a bucket to flush out any particles in the water line. Turn the saddle valve to the “OFF” position.

6.Route copper tubing to the refrigerator location.

compression nut copper tubing

1

sleeieunidn

7.Slide compression nut and sleeve over water line.

8.Connect union to compression nut -and sleeve and tighten. Do Not overtighten.

Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents IttchenAiid Custom door panels and top grille panels Before you startParts that must be ordered separately or custom-made Door panel kitsFront Dimensions for built-in areaTipping Radius Optional Top Grilles Product dimensionsLevelers extended l/8 below rollers ‘Top grilleDecorative panels Custom door Panels, handle Inserts and top grille panelsRefrigerator Product dimensions +/- I/W toleranceSide trim To do so may result in water damage Recommended grounrling methodUse only 114 copper tubing for water line Product/Property DamageInjury or property damage When a soffit is not availableProduct support Failure to follow these instructions couldNow start Film until refrigerator is completely installedPosition III Set If built-in refrigerator does not operate How to arrange for ServiceIf you need Assistance

2000495 specifications

The KitchenAid 2000495 is a versatile kitchen appliance designed to elevate your culinary experience with its robust performance, innovative technology, and user-friendly features. This stand mixer is particularly favored by both home cooks and professional chefs for its reliability and impressive capabilities.

One of the standout features of the KitchenAid 2000495 is its powerful motor. With a high-performance 325-watt motor, this mixer can handle heavy mixtures with ease, making it ideal for tasks like kneading dough or whipping heavy creams. The motor is designed to deliver consistent power at all speed levels, ensuring that your ingredients are mixed thoroughly every time.

The KitchenAid 2000495 boasts a unique planetary mixing action, which allows the beater to rotate in two directions. While the beater rotates, it moves in a planetary motion around the bowl, covering every inch and ensuring that all ingredients are incorporated evenly. This technology minimizes mixing time and maximizes efficiency, allowing users to achieve perfect results faster.

Another key characteristic of this mixer is its 10-speed slide control, which lets you choose the optimal speed for your specific mixing task. Whether you’re gently folding ingredients or mixing at high speeds, the precise control allows for complete customization of your mixing experience. The speeds range from a slow stir to a fast whip, accommodating a variety of cooking techniques and recipes.

The KitchenAid 2000495 also features a generous 4.5-quart stainless steel mixing bowl that comes with a comfortable handle. This bowl size is suitable for most standard recipes, and the stainless steel material ensures durability, ease of cleaning, and resistance to stains and odors.

Additionally, this mixer offers versatility with its optional attachments. You can expand the mixer’s capabilities by attaching various accessories, such as a pasta maker, food grinder, and vegetable slicer, transforming it into a multifunctional kitchen tool.

User convenience is at the forefront of KitchenAid’s design, reflected in features such as a tilt-head design for easy access to the bowl and a locking mechanism that stabilizes the mixer during operation. The unit is available in multiple colors, allowing you to choose one that complements your kitchen aesthetic.

In summary, the KitchenAid 2000495 is an indispensable kitchen appliance that combines power, functionality, and design. Whether you’re baking bread, preparing sauces, or mixing batters, this stand mixer is built to assist you in achieving culinary excellence with ease and style.
Top Page Image Contents