KitchenAid 6899552, 883298 dimensions Opening, Preparation, Power, Upper

Page 4

Electrical Shock Hazard

l Electrical ground is required on this appliance.

lDo Not ground to a gas pipe.

lDo Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical

shock.

q A U.L.-listed conduit connector must be used at each end of the power supply cable.

q Allow some slack in the cable so appliance can be moved if servicing is ever necessary.

Wire sizes (COPPER ONLY) must conform with rating of the appliance, as specified on the serial/rating plate, and to the requirements of the National Electrical Code, ANSI/NFPA 70-latest edition (*See Page I), and all local codes and ordinances.

- / Emounting template

9 Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.

Failure to follow these instructions could result in a fire, serious injury or death.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

q A 120-volt, 60-Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides of the line.

q A time-delay fuse or circuit breaker is recommended.

q CONNECT WITH COPPER WIRE ONLY.

q Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire).

Wiring

diagram is shown on the back cover of

support

these

instructions.

mounting

 

 

bracket

Power

cable

opening

 

SUPPlY

 

 

 

 

cable

 

 

 

support

F po

 

 

 

system

 

Electrical

Shock Hazard

 

Care must be taken when drilling holes into

 

ceiling or wall. Electrical wires may be

 

concealed behind the ceiling or wall covering.

 

 

Failure to

do so could

result in fire, electrical

 

DI I

shock or other personal injury.

1.Determine and clearly mark a vertical centerline on ceiling where range hood will be installed.

2.Use template to determine the proper location for the power supply cable opening. Drill a l-1/4” diameter hole through the ceiling at this point.

Preparation

Property/Product Damage

. Cover countertop, cooktop or range with a thick, protective covering.

l Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust duct.

l Because of the size and weight of this range hood, the support system must be securely attached to the ceiling.

-For plaster or sheet rock ceilings, the support must be attached to joists.

-If this is not possible, you must build a support structure behind the plaster or sheet rock.

l Do Not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

9 Securely attach

support

mounting bracket to

 

ceiling BEFORE

attaching

canopy.

I

 

 

 

Failure to follow these instructions may result in property or product damage.

1 Put a thick, protective covering over

n countertop, cooktop or range to protect from damage or dirt. Select a flat surface for assembling the unit. Cover that surface with a protective covering and place all range hood parts and hardware on it.

2 Determine and mark the centerline on the

n ceiling where the range hood will be installed.

Using the mounting template, mark the

3 n location of the support mounting bracket holes, ductwork and power supply cable cutouts on the ceiling. Use drill and saber saw to cut openings for power supply cable and ductwork. (See “Venting requirements” and “Electrical requirements,”

Pages 2-3).

Install ductwork.

(See “Venting requirements”

4 n section, Page 2.)

Use caulking to seal exterior

wall or roof openings.

 

5 Run wiring through ceiling according to the n National Electrical Code and local codes and

ordinances. Feed enough power supply cable through the wall to make the connections in the hood’s terminal box. Do Not turn on power until installation is completed. Use caulking to seal all openings.

upper +

chimney trim

lower -D chimney trim

w

support system

mounting

 

 

template

+attach upper chimney to

support

sttGture . first

upper

b chimney trim

eattach lower chimney

lower

- chimney trim

power

yplv cai3le

#J

Page 3

Image 4
Contents Table of Contents Quick ReferenceMobile home installation Tools neededParts needed Important Observe all governing codes and ordinancesFor the most efficient and quiet operation Venting methodsCalculating the ductwork length ~,..,&~Power OpeningPreparation UpperInstall chimney sections Electrical connectionCleaning MaintenanceIf you need service Check operationLength of Warranty Limited ONE-YEAR Internal blower

6899552, 883298 specifications

The KitchenAid 883298,6899552 is one of the leading appliances in the KitchenAid line, designed specifically to enhance cooking experiences. This versatile kitchen machine stands out with its blend of functionality, advanced technology, and elegant design, making it a must-have for both novice cooks and expert chefs.

One of the main features of the KitchenAid 883298,6899552 is its powerful motor, which ensures consistent performance whether you're mixing, kneading, or whipping. This motor offers multiple speed settings, allowing users to tailor their mixing speed to the specific needs of each recipe. From gently folding in flour to whipping egg whites into stiff peaks, this appliance provides the control needed for optimal results.

The robust mixing bowl is another highlight, featuring a capacity that can accommodate large quantities of ingredients, making it ideal for batch cooking and baking. The bowl is also designed for easy attachment and detachment, ensuring a smooth cooking process. The stainless steel construction means it is not only durable but also easy to clean, maintaining its luster even after frequent use.

Innovative technologies such as the planetary mixing action are integrated into the KitchenAid 883298,6899552. This mechanism ensures that the mixing attachment moves in a circular motion while also rotating around the bowl's perimeter, resulting in thorough and efficient mixing. This technology minimizes the need for manual scraping and helps achieve consistent textures and flavors in your culinary creations.

Another characteristic that sets this model apart is its compatibility with a wide range of attachments. From pasta makers to food grinders, the KitchenAid 883298,6899552 can transform into a multi-functional kitchen tool. This versatility enables users to explore numerous cooking styles and recipes, making it an investment that grows with your culinary skills.

The iconic design of the KitchenAid 883298,6899552, available in various colors, seamlessly fits into any kitchen decor. Its timeless aesthetic combines both form and function, making it not just an appliance but also an attractive kitchen accessory.

In summary, the KitchenAid 883298,6899552 is characterized by its powerful motor, generous mixing bowl, advanced planetary mixing technology, and compatibility with various attachments. Together, these features and technologies make it a top choice for those looking to elevate their cooking and baking experiences.