KitchenAid KERS807SBB Adjust LevelingLegs, Install Anti-Tip Bracket, Freestanding Ranges

Page 8

Freestanding Ranges:

1.Measure the distance of the countertop to the floor.

2.Then measure from the top of the range cooktop trim to the floor.

A

A. Distance from the top of the range cooktop trim to the floor

3.Your leveling height will be the difference between the 2 measurements you have just taken.

Adjust LevelingLegs

1.If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

2.Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

3.When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final position, check that the anti- tip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

Install Anti-Tip Bracket

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard or hardboard.

1.Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back page of this manual.

2.Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall, molding or cabinet.

3.Tape template in place.

4.If countertop is not flush with cabinet opening edge, align template with overhang.

If cabinet opening is wider than specified in the “Location Requirements” section, adjust template so range will be centered in cabinet opening.

5.To mount anti-tip bracket to wood floor, drill two ¹⁄₈" (3.2 mm) holes at the positions marked on the bracket template. Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a ³⁄₁₆" (4.8 mm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Remove template from floor.

6.Tap plastic anchors into holes with a hammer.

7.Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Depending on the thickness of your flooring, longer screws may be necessary to anchor the bracket to the subfloor. Longer screws are available from your local hardware store.

8.Move range close enough to opening to allow for electrical connections to be made. Remove cardboard or hardboard from under range.

9.Make electrical connections as described in the “Electrical Connection” section.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents W10118260A Range Safety Table DES MatièresLocation Requirements Installation RequirementsToolsand Parts Mobile Home Additional Installation Requirements Product Dimensions Freestanding RangeMobile home installations require Slide-in RangeElectrical Connection Cabinet DimensionsElectrical Requirements U.S.A. Only If connecting to a 4-wire system If connecting to a 3-wire systemWire receptacle 14-50R Wire receptacle 10-50RInstallation Instructions Countertop PreparationUnpack Range Measure for Proper HeightFreestanding Ranges Adjust LevelingLegsInstall Anti-Tip Bracket Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Electrical Connection U.S.A. OnlyWire connection Power Supply Cord Style 2 Direct wire strain reliefRemovable retaining nut Strain relief Black horizontal cross brace Flexible conduitDirect Wire Installation Copper or Aluminum Wire Wire Connection Direct WireInsert wire under screw clamp Hex washer head screw VerifyAnti-Tip Bracket LocationLevel Range Supply cableComplete Installation For power supply cord-connected rangesFor direct-wired ranges Moving the RangeExigences Dinstallation Sécurité DE LA CuisinièreOutillage et pièces Outillage nécessaireExigences demplacement Pièces nécessairesPlanchette de remplissage arrière facultative Lors de l’utilisation d’un cordon d’alimentation électrique³⁄₄ 14,6 cm B 76,2 cm Dimensions du produit Cuisinière autoportanteCuisinière coulissante Dimensions du placard Largeur de louverture 30 76,2 cm minSpécificationsde l’installation électrique Préparation du plan de travailInstructions Dinstallation Déballage de la cuisinièreMesurespour une hauteur appropriée Cuisinières coulissantesInstallation de la bride antibasculement Ajusterles piedsde nivellementRéglage de laplomb de la cuisinière Vérification de lemplacement de la bride AntibasculementAcheverl’installation Déplacement de la cuisinière Cuisinières alimentées par cordon dalimentationPour les cuisinières avec câblage direct Si la cuisinière ne fonctionne pas, contrôler ce qui suitHoles in bracket Trous dans la bride W10118260A All rights reserved

KERS807SBB specifications

The KitchenAid KERS807SBB is a standout in the realm of kitchen appliances, renowned for its versatile cooking capabilities and stylish design. This range combines technology, efficiency, and aesthetic appeal, making it an ideal addition to any modern kitchen.

One of the key features of the KERS807SBB is its large capacity oven, which offers a generous 6.4 cubic feet of cooking space. This ample size allows home cooks to prepare multiple dishes simultaneously, ideal for family gatherings or dinner parties. The oven is equipped with a True Convection cooking system, which employs a third heating element and a powerful fan that circulates hot air throughout the oven. This technology ensures even baking and roasting, eliminating hot spots and ensuring that every dish is cooked to perfection.

The range boasts a sleek stainless steel finish, which not only enhances its durability but also adds a touch of elegance to any kitchen decor. Its glass touch controls make adjusting settings and selecting cooking modes intuitive and user-friendly. The oven also features an adaptive bake function that adjusts cooking time and temperature for various dishes, enhancing cooking precision.

In addition to its impressive oven capabilities, the KERS807SBB offers a powerful cooktop with five burners, including a high-output burner that provides intense heat for quick boiling or searing. The burners include a simmer setting, perfect for delicate sauces or melting chocolate. All burners are designed for easy cleanup, featuring sealed designs to prevent spills from reaching the burner compartment.

The range also includes a self-cleaning feature that simplifies maintenance and upkeep, saving time and effort for busy home cooks. Its Warm Hold feature ensures that food remains at the perfect temperature until serving, providing peace of mind during meal preparation.

In terms of energy efficiency, the KERS807SBB is designed to minimize energy consumption while delivering high performance. It’s a perfect blend of modern technology and classic design, making it a practical and stylish choice for anyone looking to elevate their culinary experience.

With its premium features and user-friendly technologies, the KitchenAid KERS807SBB is more than just a cooking appliance; it's an essential tool for any home chef seeking reliability, efficiency, and sophistication in the kitchen.
Top Page Image Contents