Before you start...
Your safety and the safety of others are very important.
We have provided many important safety messagesin this manuaIand on your appliance. Always readand obey all safety messages.
This is the safety abrt symb0i.
This symb0t abrts you to potential hazards that can kiii or hurt you and others.
Ati safety messageswiii f0ii0w the safety alert symbol and either the word "DANGER"or "WARNING". These words mean:
Cabinet opening dimensions
25" (63.5 cm) countertop depth (with or without backsplash)
and 24" (61 cm) base cabinet depth, 36" (91.4 cm) countertop height
Freestanding |
| max. | / |
|
|
| |
Range | upper cabinet depth | _'_l | For minimum | 18" (45.7 cm) | |||
upper cabinet to | |||||||
|
|
|
| ||||
30" | (76.2 | cm) | cabinet clearance to | ||||
| countertop | ||||||
|
|
|
|
|
| ||
opening width
30" (76.2 cm)
_ ,_ opening width
3"
(7.6 cr_
(22.9 cm)
4" (10.2 cm) rain. clearance
You can be kilbd or sed0usly injured if you don't follow instructions.
AII safety messageswilI teli you what the p0tentiai hazard is, teli you how to reduce the chance of injury, and teii you what can happenif the instructions are not followed.
WARNING: _f the information in this
manual is not folmowed exactly, a fire or explosion may resuJt causing
property damage, personal injury or death.
- Do not store or use gasoline or
from both sides of range to side wall or other
combustible material.
Gas tine opening can be located within this
area.
6"
!(15.2 cm)
.10" Outlet shoutd be
cm) located within the 18" x 10" (45.7 cm x 25.4 cm) shaded area.
| I |
I |
\floorgas,he
\ | opening if | directly | _. I | |
below | regulator |
| ||
| 7/8" | (2.2 | cm) rain. |
|
| required | between |
| |
|
| opening |
| |
| and | door | or hinge |
|
| opening. |
|
| |
other flammabme vapors and liquids in the vicinity of this or any other appliance.
o Do not try to _ight any appliance.
o Do not touch any e_ectrica_ switch
o Do not use any phone in your building.
o Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
o if you cannot reach your gas supplier, call the fire department.
-installation and service must be performed by a qualified installer, service agency or the gas supplier.
In the State of Massachusetts, the following installation instructions apply:
•Installations and repairs must be performed by a qualified or licensed contractor, plumber, or
gasfitter qualified or licensed by the State of Massachusetts.
•If using a ball vaK,e, it shaft be a
•A flexible gas connector, when used, must not exceed 3 feet.
Slide-in
|
|
|
| _ |
|
|
|
| _j_._ |
4" (10.2 cm) rain. |
|
| ||
clearance | from | both | sides / | I |
of range | to side | wali | or __ | ",.,_.,_/" |
other combustible matehal. | " m,," | |||
|
|
|
| ¢ |
|
|
| (22.9 | cm) |
(7.6 cm)
Gas line opening should be tocated within this
shaded area.
floor gas fine opening directly below
max. upper |
|
|
| f | |||
|
|
|
| For minimum | 18" (45.7 cm) | ||
cabinet |
| depth | _ | upper cabinet | |||
| clearance | to | |||||
| to countertop | ||||||
30" (76.2 | cm) cabinet | ||||||
cooktop, | see | ||||||
| |||||||
|
|
|
|
| |||
|
|
|
| ***NOTE |
| ||
opening | width |
|
|
|
| ||
30" (76.2 | cm) |
|
|
|
| ||
opening | width |
|
|
|
| ||
IMPORTANT:
Rear vent must be instalbd on all
models for proper
ventilation. See Step 7, Panel D.
Outlet should be located within the 18" x 10"
(61 cm) (45.7 x 25.4 cm) shaded area.
7/8" (2.2 cm) min. required between pening and door or hinge
opening.
Countertop opening dimensions that are shown
must be used. Given dimensions provide required clearances.
When installing a range under existing cabinets and the installation does not meet the minimum
cabinet clearances, install a range hood above the range to avoid burn hazards.
Read electrical and carpentry instructions.
Proper installation is your responsibility. A qualified technician must install this range. Make sure you have everything necessary for correct installation. it is the customer's responsibility to make sure that the countertop has been properly prepared and that the installation clearances specified on the model/serial rating plate are met. The model/serial rating plate is located on the oven frame behind the oven drawer.
Check location where range wifl be installed. The range should be located for convenient use in the kitchen. Recessed installations must provide complete enclosure of the sides and rear of range.
Aft openings in the wall or floor where range is to be installed must be sealed.
IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and
It is the customer's responsibility:
To contact a qualified electrical instafler.
To assure that the ebctrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
NOTE: This appliance is manufactured for use with Natural Gas. Conversion to LR Gas can be made
using the kit included in your literature package.
NOTE: The metal chassis of the range must be grounded in order for the control panel to work. If the metal chassis of the range is not grounded, no keypads will operate. Check with a qualified electrician if you are not sure the range is grounded.
IMPORTANT: Observe all governing codes and ordinances.
Grounded ebctdcal outlet is required. See "Electrical requirements," Panel C.
Cabinet opening dimensions that are shown must be used.
Do not pinch the power supply cord between the range and the wall.
Do not seal range to side cabinets.
Copies of the standards listed may be obtained from: *National Fire Protection Association
One Batterymarch Park Quincy, Massachusetts 02269
**CSA International
8501 East Pleasant'Valley Road Cleveland, Ohio
***NOTE 24" (6I cm) rain. when bottom of wood or metal cabinet is protected by not less than 1/4"
(6.4 mm) flame retardant miltboard covered with not tess than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 ram) copper.
30" (76.2 cm) rain. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.
Panel A