All connections must be wrench-tightened.
pressure regulator and valve assembly
flexible manual
connector shutoff valve
etbow
J
1/2" (I .3 cm) flare union adapters
the gas supply pipe to the pressure 1Assemble the flexible connector from m regulator, located in the lower left side
of the storage drawer area, in this order: shutoff valve, 1/2" (1.3 cm) flare union adapter, flexible connector, 1/2" (1.3 cm) flare union adapter. Seal
all openings in floor or wall wherever range is installed.
for use with LR gas to seal all gas
I Use
used, be certain connectors are not kinked.
supply line. Wait a few minutes for the j Open the shutoff valve in the gas
m gas to move through the gas line.
ITestIconductedfor gasaccordingleaks. Leakto thetestingfollowingshall be mJinstructions:
Test all connections by brushing on an approved
show a leak. Correct any leak found.
B"8888" should appear in clock display. Plug into a grounded 3 prong outlet.
I2 1 Remove vent cap, cooktop burner caps ml and grates from parts package. Align
notches in burner caps with pins in burner base. Burner caps should be level when properly positioned. Place burner grates over burners and caps. Place vent cap over vent dome.
cap
vent
er
vent | _ | grate |
Adjust the height of top burner flames (some models)
The cooktop LOW burner flame should be a steady blue flame approximately 1/4" (0.64 cm) high. It can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly underneath the control knob.
If the LOW flame needs to be adjusted:
a. Remove the control knob.
b. Hold the knob stem with a pair of pliers. Use a small
turn the screw located in the center of the control knob stem
until the flame is the proper size.
c. Replace the control adjustment
knob.screw,
d. Test the flame by
turning the control from "LO" to "HI", checking the flame at each setting.
Top burner flame appearance:
towflame
high flame
oven bottom and place it on a protected
I2 5 ] Remove the oven rack. Removethe m surface.
burner. Push the "BAKE" pad and
i2 6 ] Check the operation of the oven
m ,350oF, will appear in the temperature display. Press the "START" pad. "LO" will appear in the display; then "170°R''The oven burner should light in 50 to 60 seconds. This delay is normal. The oven safety valve requires a certain time before it will open and allow gas to flow.
Electric ignitors are used to light the oven and broil burners.
Do not insert any object into the opening of the protective shield that surrounds the ignitor.
Do not clean the area.
Push "CANCEL/OFF' pad. Insert oven bottom tabs into slots in oven burner
area. Check that tabs are correctly placed in slots. If the oven bottom is not positioned properly, poor baking performance could occur. Replace oven racks.
Check the operation of the
oven broil burner. Close the oven door. Press the "BROIE'pad. "500 F'will
appear in the temperature display. Press the "START" pad. The oven broil burner should light in 50 to 60 seconds. This delay is normal. The oven safety valve requires a certain time before it will open and allow gas to flow. The first time broil burner is lighted, it may take longer to light because of air in gas line. The first few times burner is used sparks may appear. This is normal. NOTE: Oven door must be shut for broil burner to operate.
Look through oven window to check broil burner for proper flame. The flame should have a uniform, light blue
appearance around the burner surface. No yellow tips, blowing or lifting of the flame should occur. NOTE: The first few times the broil burner is used, yellow sparks may appear in the flame. This is
normal and will stop after burner has been used a few times.
Press the "CANCEL/OFF' pad. If the broil burner flame needs adjustment, contact your KitchenAid dealer or
authorized service company for assistance.
/
Insert storage drawer into slide rails on sides of drawer opening. Lift front of drawer slightly and push firmly to
close drawer.
E ectronic gnition System E
oven
as conversion
No attempt shall be made to convert the range
Initial lighting and gas flame adjustments.
rear
from the gas specified on the model/serial rating
Cooktop and oven burners use electronic ignitors in place of standing pilots. When the cooktop
j ignitor
plate for use with a different gas without consulting
control knob is turned to the "LITE" position, the system creates a spark to light the burner. This
sparking continues as long as the control knob is turned to "LITE".
the servicing gas supplier. An L.R Gas Conversion Kit is included in your literature package.
When the oven control is turned to the desired setting, a glow bar heats up bright orange and ignites the gas. No sparking occurs and the glow bar remains on while the burners operate.
| i | operation of |
|
| OFF |
| Check the |
|
| • | |
| m | the cooktop |
|
| |
turn each | control knob |
|
|
| |
to the | "LITE" position. | _ | {_ |
| |
burners. Pushinand |
| ||||
The flame | should light |
|
|
| |
within | 4 seconds. The |
|
|
| |
first time a burner is | _ | ". _ | ) | ||
lighted | it may take |
| "G,_ | ||
longer | than 4 seconds |
| _, _ , _ _o | ||
to light | because of air in |
| @_D M_.o | ||
gas line. |
|
|
| LO | |
cooktop control knob to the "OFF" l lf burners do not light properly, turn
m position. Check that the power supply cord is plugged in and the circuit breaker or fuse has not blown. Check that the gas shutoff valves are set to the "OPEN" position. Repeat Step 22. If a burner does not light at this point, contact your KitchenAid dealer or authorized service company for assistance.
oven burner
This flame should have a 1/2" (1.3 cm)
I2 7 1 Check the oven burner for proper flame. m long inner cone of
outer mantle of dark blue, and should be clean and soft in character. No yellow tips, blowing or lifting of flame should occur.
| air shutter - | |
locking screw | rotate | to |
adjust | for | |
".. | proper | flame |
oven burner air shutter
location \
| brass | orifice |
oven burner | hood | (nut) |
locate the air shutter near the center
I28 ] If the oven flame needs t° be adjusted' m rear of range. Loosen the locking screw
and rotate the air shutter until the proper flame appears. Tighten locking screw.
To get the most efficient use from your new range, read your Use and Care Guide. Keep Installation
Instructions and Guide close to range for easy reference.
PaneU E