Excessive Weight Hazard

Now start...

WARNING

Use two or more people to move and install external blower.

Failure to do so can result in back or other injury.

1. Discard any cardboard packaging from the blower wheel.

2. Attach the black plastic vent collar to the exterior blower using the four screws provided.

3. Remove the back cover, wiring box cover and electrical wiring knockout.

4. In the knockout, attach the U.L./CSA-listed strain relief.

Note: For most installations, it is recommended that the strain relief be installed so that it can be tightened from inside the exterior blower housing.

5. Reattach the wiring box cover loosely. It will be removed again in Step 2 of “Making electrical and vent connections.”

Follow the instructions for your type (wall or roof) installation.

WALL INSTALLATIONS

1. Choose a location on an outside wall where no wall studs, wires, pipes, etc. run through the opening area. A minimum distance of 24" (61 cm) from exterior blower to ground may be required depending on local code. Make sure to leave room for anticipated snowfall in your region.

2. Drill the guide hole in the center of the 11" (27.9 cm) diameter opening area.

3. Mark a 27-1/2" x 34" (69.9 x

86.4cm) rectangle on wall as indicated in FIGURE 1.

4. Cut a rectangular hole in the siding only. Do not cut sheathing. Nail down all siding ends.

5. Mark an 11" (27.9 cm) diameter circle around Guide Hole as indicated in FIGURE 1. Mark center of the 1-1/4" (or

3.0cm) diameter hole for electrical wiring as indicated in FIGURE 1.

6. Cut 11" (27.9 cm) diameter hole in sheathing. Drill the 1-1/4" (or 3.0 cm) diameter electrical wiring hole.

7. Run a large bead of caulk on the back side of the housing along the outer edge.

8. Center the exterior blower ring in the 11" (27.9 cm) diameter hole, making sure that the 1-1/4" (or 3.0 cm) diameter electrical wiring hole lines up with the hole in the wiring box.

9. Attach the exterior blower to wall using screws appropriate for your installation. All four holes in the back panel must be filled to prevent moisture that may get inside the exterior blower housing from leaking into the home.

10. Seal all around the mounting screw heads with caulk.

11. Go to "Making electrical and vent connections", Page 4.

ROOF INSTALLATIONS

1. Choose location on rear slope of roof that minimizes vent run. Avoid obstacles such as TV leads, electric lines, etc. If exterior blower top is level with roof peak, it will not be seen from street. Remember this location as you work from inside the attic.

2. Mark a point half-way between the rafters and drill a guide hole at this point.

3. From the outside, using the guide hole as a starting point, mark the rectangular cut-out as indicated in FIGURE 2. Remove only the shingles in this area.

4. Mark an 11" (27.9 cm) diameter circle around guide hole as indicated in FIGURE 2. Mark center of the 1-1/4" (or

3.0cm) diameter hole for the electrical wiring as indicated in FIGURE 2.

5. Cut out the roof boards along the 11" (27.9 cm) diameter circle. Drill the 1-1/4" (or 3.0 cm) diameter electrical wiring hole.

14"

(35.6 cm)

34"

(86.4 cm)

9-3/8"

(23.8 cm)


	10-5/8"
1-1/4"				(27 cm)
(3.0 cm)			15"
(3.0 cm)			15"
dia. hole		(38.1 cm)
dia. hole		(38.1 cm)
				27-1/2" (69.9 cm)
				27-1/2" (69.9 cm)

11" (27.9 cm)

dia. hole

guide

hole

12-3/4"

hole

(32.4 cm)

23"

(58.4 cm)

9-3/8"

(23.8 cm)

FIGURE 1

FIGURE 2

1-1/4"

10-5/8"

(for wall

(for roof

(27 cm)

installations)

(3.0 cm)

13-3/4"

installations)

dia. hole

(34.9 cm)

25" (63.5 cm)

Page 3

KPEU722M specifications

The KitchenAid KPEU722M is a versatile and innovative kitchen appliance designed to elevate your culinary experiences. Renowned for its durability and performance, this appliance embodies KitchenAid’s commitment to quality and user-friendly design.

One of the standout features of the KPEU722M is its powerful motor, which delivers excellent performance across various cooking tasks. Whether you are kneading dough, whipping cream, or mixing batters, this kitchen tool can handle it all with ease. The motor is designed for both efficiency and longevity, ensuring that it can withstand the demands of regular use in a busy kitchen.

Another key characteristic of the KPEU722M is its advanced planetary mixing action. This unique technology allows the mixing bowl to rotate while the beater moves in the opposite direction. As a result, all ingredients are thoroughly mixed and incorporated, delivering consistent results every time. This feature is particularly beneficial when making bread or chiffon cake, where uniform blending is essential.

In terms of design, the KPEU722M boasts an elegant and modern aesthetic that can complement any kitchen decor. It is available in various colors, allowing users to choose one that best fits their style. The appliance is also engineered for ease of use, with intuitive controls that provide a seamless user experience.

The KPEU722M comes with a range of attachments, including a flat beater, dough hook, and wire whip, further enhancing its versatility. Each attachment is designed to cater to specific tasks, enabling users to experiment with different recipes and techniques. Additionally, the bowl is spacious, allowing for large batches to be prepared at once, making it ideal for family gatherings or baking marathons.

Safety features are another hallmark of the KPEU722M. It incorporates a thermal overload protection system that protects the motor from overheating, ensuring the appliance operates safely during extended use. Furthermore, the non-slip base provides stability while mixing, preventing any accidents.

Overall, the KitchenAid KPEU722M is a powerful and stylish kitchen appliance that brings advanced mixing technology and convenience to the home cook. With its robust performance, thoughtful design, and essential features, it is a valuable addition to any kitchen, ideal for both novice chefs and seasoned professionals.