KitchenAid W10278586A Replace Doors and Hinges, Remove and Replace Freezer Drawer, Final Steps

Page 6

3.Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4.Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

5.Remove top hinge cover from left side refrigerator door.

6.Remove the façade from the front of the top of the cabinet. Remove the screw on the backside of the center of the façade, then slide the façade forward and out from under the hinge.

7.Disconnect the wiring plug located on top of the hinge by wedging a flat-blade screwdriver or your fingernail between the two sections.

8.Disconnect the water line by pulling back on the locking collar while pulling the water line out of the water line connector.

9.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

10.Using a ³⁄₈" hex wrench, remove the leveling leg brackets from the bottom of the cabinet. Keep screws for later use.

Replace Doors and Hinges

1.Assemble the parts for the top hinges as shown in Top Hinge graphic. Do not tighten the screws completely.

2.Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Align the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4.Reconnect the wiring plug on top of the left-hand side refrigerator door.

5.Reconnect the water line by pulling back the locking collar ring while firmly pushing the water line into the connector.

6.Check for leaks. Replace the façade and top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to remove and replace the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1.Open the freezer drawer to full extension.

2.Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3.Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1.Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

2.Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets. See Drawer Front Replacement graphic.

3.Completely tighten the four screws.

Adjust the Doors

There are two leveler foot screws located at the base of the refrigerator. If your refrigerator seems unsteady or you want the door to close more easily, use the following instructions.

1.Using a ¹⁄₄" hex driver, turn the leveling screw on each side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws which makes them easier to turn. It may take several turns of the leveling screw to adjust the tilt of the refrigerator.

■To raise, turn the leveling screw clockwise.

■To lower, turn the leveling screw counterclockwise.

A

A. Leveling screw

2.Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same amount.

3.Replace the base grille.

Final Steps

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Return all removable parts to doors and drawer and food to refrigerator and freezer.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Refrigerator Safety Refrigerator User InstructionsUnpack the Refrigerator Installation InstructionsClean Before Using Remove the PackagingWater Supply Requirements Location RequirementsElectrical Requirements Recommended Grounding MethodConnect the Water Supply Remove and Replace Handles Complete the InstallationRefrigerator Doors and Drawer Remove Doors and HingesRemove and Replace Freezer Drawer Adjust the DoorsReplace Doors and Hinges Final StepsDrawer Front Removal Drawer Front Replacement Using the Controls Refrigerator USEOpening and Closing Doors USB Port FeaturesPhotos Upload Photos to the DisplayCrisper Humidity Control Water and Ice Dispensers Ice Maker and Storage Bin Water Filter Status Light CleaningRefrigerator Care Water Filtration SystemTroubleshooting Changing the Light BulbRefrigerator Operation Temperature and Moisture Ice and WaterWater and ice dispenser will not operate properly Water Filter CertificationsOff-taste, odor or gray color in the ice Water is leaking from the dispenser systemProduct Data Sheets Application Guidelines/Water Supply ParametersModel UKF8001AXX-200 Capacity 200 Gallons 757 Liters Kitchenaid Refrigerator Warranty This limited warranty does not coverInstructions Dutilisation DU Réfrigérateur Sécurité DU RéfrigérateurInstructions D’INSTALLATION Exigences demplacementDéballage du réfrigérateur Spécifications de l’alimentation en eau Méthode recommandée de mise à la terreSpécifications électriques Pression de leauRaccordement de la canalisation deau Raccordement à une canalisation d’eauRaccordement au réfrigérateur Portes et tiroir du réfrigérateur Achever l’installationEnlèvement et réinstallation des poignées Enlèvement des portes et des charnièresAjustement des portes Réinstallation des portes et des charnièresRetirer et réinstaller le tiroir du congélateur Étapes finalesEnlèvement et réinstallation de la porte Utilisation des commandes Utilisation DU RéfrigérateurOuverture et fermeture des portes Port USB Ajustement des commandesCaractéristiques Télécharger des photos vers laffichageMesure Effacer les photos de laffichageDiaporama Options VerrouillageRéglage de lhumidité dans le bac à légumes Distributeurs d’eau et de glaçonsLe distributeur de glaçons Volumes préréglésPlateau coulissant Distribution de glaceMachine à glaçons et bac d’entreposage Système de filtration de leau Entretien DU RéfrigérateurTémoin lumineux de l’état du filtre à eau NettoyageRemplacement de l’ampoule d’éclairage DépannageFonctionnement du réfrigérateur Température et humidité Glaçons et eauGoût, odeur ou couleur grise des glaçons ’eau coule du système de distributionLeau du distributeur est tiède Feuilles DE Données SUR LE Produit Système de filtration d’eau intérieurModèle UKF8001AXX-200 /Capacité 200 gallons 757 litres Kitchenaid Refrigerator Warranty W10278586A SP PN W10278589A All rights reserved

W10278586A specifications

The KitchenAid W10278586A is a high-performance kitchen appliance designed to elevate the culinary experience for home chefs. This versatile product is engineered with advanced technology that not only enhances functionality but also promotes efficiency in food preparation. One of the standout features of this model is its powerful motor, which provides the necessary strength to handle a variety of mixing tasks, from kneading pizza dough to whipping cream. This robust motor ensures consistent results, making it an indispensable tool in any kitchen.

Another significant characteristic of the W10278586A is its multi-speed control. This feature allows users to select the appropriate speed for their specific task, whether they are gently folding ingredients or mixing at high speeds. The intuitive controls are easy to navigate, providing precision and confidence in every use. The appliance’s design also integrates a soft-start feature, which gradually increases speed to prevent splattering, particularly useful when combining dry ingredients with wet ones.

In terms of build quality, the KitchenAid W10278586A is constructed with durable materials that ensure longevity and withstand the rigors of daily use. The stainless steel bowl not only has a sleek appearance but is also resistant to scratches and dents. Additionally, the bowl is large enough to accommodate a sizeable batch of ingredients, making it ideal for family-sized meals or entertaining guests.

The W10278586A also features a tilt-head design, allowing users to easily access the mixing bowl and incorporate ingredients without hassle. This convenience is complemented by a selection of attachments, including a wire whip, dough hook, and flat beater, which enables users to tackle a wide range of recipes with ease.

Aesthetic appeal is also a key aspect of the KitchenAid W10278586A, available in various colors to suit different kitchen decors. This appliance is not just functional but also acts as an attractive addition to the countertop.

In summary, the KitchenAid W10278586A combines power, versatility, and style, making it an essential appliance for both novice and experienced cooks alike. With its array of features and reliable performance, this model is sure to inspire culinary creativity in any household. Whether you are baking, whipping, or mixing, the KitchenAid W10278586A stands ready to assist in delivering delicious results every time.
Top Page Image Contents