KitchenAid Garbage Disposal installation instructions So sink flange. ,?, 8Attach, Grounding

B. Remove nut at top of sink strainer Remove extension pope.

C. Loosen the large-diameter nur at the base of the strarner by placmg the tip of d screwdwer on the rldjr of the nut and

gently tapp~nj the wrwdrlver ~0th a hammer

D. Remove nut

E. Push the straner assembly up through the sink hole and remove

5 Clean sink’s drain line.

If installing in a new home, go to Step 6.

Remove drain trap. Using anaujer, clean out the horlzcmtal drain pope that run5 from the trap to the main waste pipe.

6Separate the mounting assembly.

A Holdlnj the mountlnj assembly with one hand, “sethe other hand to ,nsert,am- breaker wrench Into one of the lugs of the lower mounting rlnj Turn assemblycounter- clockwse and remove

B. Loosen scr- on mountmg assembly until the/ are level with mountlnj rung surface

c. Use ScrewdrIver to pry off snap r,ng

D. Take assembb apart and set aslde

7Apply rubber asket or putty

so sink flange. ,?

aThe rubber sink flange gasket should alway; be used where powble Place rubber gasket over sink flange Go to Step 7-C

B.If slnkopenmj does not permit the “seof a

rubber seal, plumb& putty may be used Form putty rntoa long roll by roll~nj It behveen your hands Press roll under sink flange nm

C.Place flange Into sink drain hole. Fust down gently, but flrmb to make sure flange sits evenly over gasket or I” putty

8Attach the

upper mounting

~wo,‘mg ,om?::?k:p!!ond

rub&r gasket, tin the metal bsck-up ring (flat side up), up and over sink flange.

B. Holdmj ttx rubber gasket and metal back- up nng in place, attxh the mwntlng ring to the sleedve wth the three mounting rrnj screw-s Do Not bqhten screws at this t!me.

C. Push rubber gasket, metal back-up n”g and mounmg rmg further up sink sleeve. Slrde snap ring wto srnk sleeve untrl It pops Into place I” the sleeve groove.

D.Tijhten	mounting		scr-	until	entlre
mounting		assembly	IS seated		evenly and
tkhtlvawnst		sink			1D.H

9Make electrical connections.

ARemove electrical plate from the bottom

of the new disposer Pull out the black end Vmrte electrical wires Locate the green

jroundnj screw under plate.

8.Insert strain relref Into hole Insert power supply cable through strain relief. Pull cable wres through open~nj where dlswser wres are located. nghten strain relref screws.

c.Connect power supply cable bwres to the disposer wires us~nj electrical wire nut5 M

by solderlnj		wires	together Be SUR to
connectwhiietotiite,andbbckto				1)s	,,	,
black. Wrap		wore	conratlcns	with
electrical	tape. Put wires back inside
drsooser	housmq.

10Check for proper

grounding.

Electrical ground is required on this appliance.

Do NOT reconnect eletical CUrTent to main service panel until proper ground Is installed.

k If the cabk kadlng to the dlswser has three wires, attach tine green groundlnj we to the green groundlng xre.v Go to Step 10-D.

B. If the cable does NOT have a grounding wire, attach a length of copper wire (no smaller than the other cable wire) to the jreen grcwndmg screw

C. Attach theotherend of thegrwndmj wire to a grounded metal cold water pipe!

DO NOT ground to a gas sUpply line of hot water supply Ilne.

Use grounding clamp to secure wire to pipe. If noa-meta or plastrc pipe ISused in water connections or water supply, you must have a qwlified electrtcian install a proper ground.

PANEL B