KitchenAid KAD-7, KUD01 Installation Considerations, Specifications, Water Usage, Section ONE

Page 5

SPECIFICATIONS

ELECTRICAL SUPPLY: (Under Load) 60Hz, 120VAC

SUPPLY WATER FLOW RATE: (To Fill 2 Quarts (1.9 L) in 27 secs.) - 120psi Max., 20psi MIN.

SUPPLY WATER TEMPERATURE: 120° F to 160° F (49° C to 71° C)

WATER CHARGE: 1.8 Gal. (6.8 L) / First Fill

1.7 Gal. (6.5 L) / All Other Fills

LOWER SPRAY ARM ROTATION: 25 TO 40 RPM

UPPER SPRAY ARM ROTATION: 25 TO 35 RPM

APF DRAIN: .1 Gal. (.38 L) per 5 sec.

APF Pressure Switch Trip Point: 10 In. Water Column

HEATING ELEMENT HEATING RATE: 1°+ F Rise per Minute

WATER USAGE

Baked On Cookware Heavy, Normal

China - Light/China

SECTION ONE

INSTALLATION CONSIDERATIONS

GENERAL CONSIDERATIONS

For complete installation procedures see the “Installation Instructions” in the literature packet provided with the dishwasher.

A video presentation, Key Features and Installation Considerations, part number

4317280V, is available. This video covers the entire installation process.

Each location will present a different set of challenges that can be anticipated and solved before installation begins.

• Check the planned location of the dishwasher.

• Easy access to hot water, drain line and electricity.

•

Convenient access for loading. The dishwasher door should open and close freely.

•

The opening under the counter should be square and the cabinet fronts should be perpendicu-

 

lar to the floor.

Soil Level

Water

Sensed

Usage

 

(gal/L)

 

 

 

8.8 -10.4/

High

33.4 -39.4

 

 

 

6.9/

Low

26.2

 

 

Soil Level

Water

Sensed

Usage

 

(gal/L)

 

7.1-8.6/

High

26.9-32.5

 

 

 

5.5/

Low

20.8

 

 

•

Make sure the cabinet opening is free of intrusions such as braces or utility lines.

•

Do not install the dishwasher on carpeted floors.

•

An outside wall behind the dishwasher should be insulated to prevent the water line, inlet valve

 

and drain line from freezing and rupturing.

Additional Considerations

The application of a horizontal pump and filter technology allows for the tub to be designed three inches deeper than current models. This deeper

Quick Clean Up

 

 

Rinse Only

 

 

 

 

 

 

 

 

 

 

 

Water

 

First Fill

Water

 

Water

Usage

 

 

Usage

 

Temp

(gal/L)

 

 

 

 

 

 

1.8-2.1/

 

Less

6.9-8.4/

 

 

 

than

26.1-31.8

 

6.9-7.9

 

135° F

 

 

 

 

 

 

 

 

 

 

(57° C)

 

 

 

 

 

Greater

5.2-6.7/

 

 

 

 

than

19.7-25.4

 

 

 

 

135° F

 

 

 

 

tub and longer door design will impact the instal- lation process because there is less working space available underneath the unit and correct routing and placement of the drain hose, water supply and electrical wiring is critical.

The tub must be level. Reduced water consump- tion of this dishwasher requires that it be installed level and plumb for proper water recirculation back into the sump area during operation.

(57° C)

Do not remove the drain tube from the left side of the tub. If the loop is removed, the dishwasher will not initiate Automatic Purge Filtration. The drain tube also contains a check valve in the L-connector that prevents backflow of water into the dishwasher from the house- hold drain system.

Drain Tube

Main Wash Motor

 

Loop

Drain Pump

 

 

 

Motor

View of Sump Assembly from Underneath Showing Horizontal Wash Pump Motor and Drain Pump Motor

44

1

Page 4 Page 6
Image 5
Page 4 Page 6
Contents For the way its made KUD01 Stainless Steel DishwasherIntroduction Table of Contents What to do if the Dishwasher Door does not Open SafetySpecifications Installation ConsiderationsWater Usage Section ONEKeypad Matrix Model Specific TablesTheory of Operation Cycles and Cycle Variation Electronic Control Connector PinsAutomatic Purge Filtration APF Quick Clean UpStrip Circuits Wiring Diagram Canceling a CycleTech Tips Changing a CycleHi Temp Scrub Option SelectionsSani Rinse Energy Saver DryDelay Hours Diagnostic Cycle Time ChartTo Delay the Start 003 005 002 010 100Cycle Status Indicators Rapid Advance Service Feature and Diagnostics CyclesWash/Rinse Function Function DescriptionDrain Function APF Function Last Five Seconds Automatic Purge FiltrationAPF Function First Five Seconds Common Cycle Time Chart Notes Component AccessSection Three Component LocationUsing the Common Cycle Time Chart Accessing Components in the DoorCycle Progression & Status Indicators-Output Loads Electrostatic Discharge ESD Sensitive ElectronicsQuick Clean/Time Saver Cycle Removing the Door Latch AssemblyRemoving the Electronic Control Board InsetRemoving the Door Latch Microswitch HOW to USE the Common Cycle Time ChartCommon Cycle Time Chart Layout Removing the Active Vent AssemblyRemoving the Inner Feed Tube and Lower Spray Arm Removing the Dispenser AssemblyServicing Components Inside the TUB Servicing the Heating Element Removing the Water InletRemoving the Overfill Assembly Servicing the Overfill AssemblyRemoving the Overfill Control Switch Section Four Troubleshooting and DiagnosisTroubleshooting Chart Removing the Wash Motor To Remove the Volute Accessing Components in the Sump AssemblyRemoving the Impeller from the Wash Motor

KUD01, KAD-7 specifications

The KitchenAid KAD-7 and KUD01 are two prominent models from KitchenAid, known for their innovative features and modern design, enhancing kitchen functionality and aesthetics.

The KitchenAid KAD-7 is a standout refrigerator designed to combine style with practicality. This model comes with a spacious interior, boasting an efficient layout that maximizes storage while maintaining accessibility. The KAD-7 features adjustable shelves, which allow you to customize the space to accommodate various food items, from large platters to smaller containers. An external water and ice dispenser provides convenience, delivering chilled water and ice at the touch of a button, while a built-in water filter ensures freshness.

The refrigerator incorporates advanced temperature management systems, ensuring that food stays fresh for longer periods. Energy-efficient LED lighting illuminates the interior, making it easy to find items in any corner of the fridge. The sleek stainless-steel finish not only provides a modern touch but is also fingerprint resistant, ensuring it stays looking clean and shiny.

On the other hand, the KitchenAid KUD01 is a high-performance dishwasher that exemplifies efficiency and quiet operation. It boasts several wash cycles and specialized options tailored for different types of dishes, ensuring thorough cleaning results. The ProWash Cycle identifies the level of soil on dishes and adjusts the washing time accordingly, optimizing performance without wasting water or energy.

One of the hallmark technologies of the KUD01 is the PowerScour option, which uses progressive washing action to tackle tough, baked-on food. The dishwasher also features a stainless-steel interior that resists odors and ensures longevity through enhanced durability. The Whisper Quiet operation ensures that the dishwasher works silently in the background, making it an ideal choice for open-concept living spaces.

Both the KAD-7 refrigerator and KUD01 dishwasher embody KitchenAid's commitment to excellence in appliance design. Their sleek aesthetics, combined with user-friendly features, not only elevate the kitchen experience but also provide unmatched functionality and efficiency. Whether you're storing your groceries or cleaning up after a family meal, these appliances make everyday tasks simpler and add a touch of luxury to your home. KitchenAid continues to lead the way in blending technology with design, making their products a valuable addition to any kitchen.
Top Page Image Contents