KitchenAid KUDS40FVPA, KUDC03IV, KUDE70FVPA, KUDE60FVPA, KUDS30IV Install Custom Panel Option

Page 15

Custom panel dimensions - Dishwashers with control panel on the front

(65.8 cm)

(19.1 mm)

(3.2 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

Follow directions in Option 2 of “Install custom panel” section.

Install Custom Panel – Option 1

(Models KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of the custom panel, the screw holes should be countersunk for the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed the panel thickness. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

NOTE: A customer-supplied full-front panel must weigh no more than 16 lbs (7.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

NOTE: All mounting hardware supplied is for a ³⁄₄"

(19.1 mm) thick wood panel. If a thinner wood panel, or materials other than wood are used, it is the consumer’s responsibility to obtain the proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

1 Custom panel installation - Dishwashers with control panel on the top

23¹⁄₂"

 

 

*30³⁄₁₆" (76.7 cm)

(59.7 cm)

 

 

 

³⁄₄" (19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6" (15.2 cm).

With a TORX® screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

2 Custom panel dimensions— Dishwashers with control panel on the top

3 screws per side

outer panel

Gently set outer panel aside. Lay the customer-supplied custom panel face down on a covered, non-scratching surface.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents W10275503B You Need to Table of ContentsTools and Parts Location Requirements Insulation may be compressed Not used on all models Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Add 90 elbow fitting to the water supply line Route water supply lineFlush water supply line Slide nut and ferrule onto tubingWaste disposer no air gap Install Drain HoseRoute drain hose Connect drain hosePrepare Dishwasher Install Moisture Barrier under a wood countertopRemove terminal box cover Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Remove panelsDetermine Cabinet Opening Custom Panel Dimensions Install the Door Handle on some modelsModels KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA Install Custom Panel OptionAttach body panel Install custom panelMark line Mark pilot holesModels KUDC03IV and KUDS30IV Choose Attachment OptionMove Dishwasher into Cabinet Opening Check water and drain hose position Closes too quickly- Decrease spring tensionDoor falls open- Increase spring tension Connect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire-Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in strain reliefSecure Dishwasher in Cabinet Opening Check side attachment Bottom Sound Pad Installation on some modelsComplete Installation Reinstall access panelsCheck lower panel edge Power supply cord-Plug into a grounded 3 prong outletReconnect power Reconnect PowerCheck Operation If Dishwasher Does Not OperateAdditional Tips Il faut Table des matièresOutillage et pièces Exigences demplacement 60,6 Dimensions Produit et cavité d’encastrementUtilisation du dispositif de brise-siphon Exigences dévacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de connexion lutilisateur emploie-t-il? Déconnecter la source de courant électriqueFermeture de lalimentation en eau Lutilisateur possède-t-il déjà des moyens de raccordement?Raccordement direct Préparation du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Perçage du trouAcheminement de la canalisation dalimentation en eau Vidange de la canalisation dalimentation en eauEnfiler l’écrou et la virole sur la canalisation Pas de broyeur à déchets sans brise-siphon Installation du tuyau d’évacuationAcheminement du tuyau dévacuation Broyeur à déchets sans brise-siphonOption D pas de broyeur à déchets avec brise-siphon Broyeur à déchets avec brise-siphonPas de broyeur à déchets avec brise-siphon Option C broyeur à déchets avec brise-siphonDépose des panneaux Installation dun serre-câblePréparation du lave-vaisselle Placer le lave-vaisselle sur le dosCordon d’alimentation Conducteur de liaison à la terre Raccordement du cordon dalimentationTableau de réglage Hauteur du lave-vaisselle Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Mesure de louverture dencastrement du placardPlanchers surélevés Ajouter des cales si nécessaire Installation de la poignée de porte sur certains modèlesDimensions du panneau personnalisé Installation de la poignée de porteModèles KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, et KUDE70FVPA Installation du panneau personnalisé OptionMarquage de laxe Marquage des avant-trousModèles KUDC031V et KUDS301V Installation du panneau personnaliséFixation de la poignée Fixation du panneau principalOption 1, Fixation au plan de travail Choix de l’option de fixationSortir le bride Insérer la brideOption 2, Fixation au côté du lave-vaisselle Sectionnement de lextrémité de la brideInsertion des boutons en plastique Mise en position verticale du lave-vaisselleInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteRaccorder le raccord coudé de 90 à la valve Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Vérification de laplomb et réglage des pieds si nécessaireEnfilement de la bride sur le raccord Raccordement au circuit dévacuationRaccordement électrique direct Position définitive de la bride de tuyauRaccordement direct Raccordement du fil de mise à la terre Raccordement direct Raccordement des fils restantsRaccordement direct Fixation du câble dans le serre-câble Fixation du lave-vaisselle Vérification de la distance de dégagement pour la porteVérification de lespacement Lintérieur Achever linstallation Réinstallation des panneaux daccèsVérification de la fixation latérale Rétablir la source de courant électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnexion de la source de courant électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pasConseils supplémentaires Page Page Page All rights reserved
Related manuals
Manual 52 pages 48.13 Kb

KUDS40FVPA, KUDS50FVPA, KUDE70FVPA, KUDC03IV, KUDS30IV specifications

The KitchenAid W10056407A and its associated dishwasher models, including KUDE60FVPA, KUDS40FVPA, KUDS50FVPA, and KUDE70FVPA, represent a blend of innovation, efficiency, and elegant design in today’s modern kitchen appliances. These models are designed to provide exceptional cleaning power while being user-friendly.

One of the standout features of these dishwashers is their Advanced Clean Water Wash System, which uses a combination of powerful jets and filtration to ensure that every dish is cleaned thoroughly, even the dirtiest pots and pans. This technology minimizes the need for pre-rinsing, saving both time and water. The Efficient Wash Cycle allows users to customize the cleaning according to their needs, providing options for heavy-duty washing or light cycles for delicate items.

Another remarkable feature is the ProWash Cycle, which automatically determines the optimal cycle for the load being washed. This technology analyzes soil level and adjusts the wash time and water usage accordingly, making it a smart choice for those who want to conserve resources without sacrificing cleaning results. Additionally, the models boast a Quiet Operation, with advanced sound insulation technology that ensures a near-silent experience, allowing users to carry on with other activities without being disturbed by noise from the dishwasher.

The adjustable racks in models like the KUDE70FVPA make loading and unloading a breeze. The upper rack can be adjusted to accommodate taller items without compromising space in the lower rack, enhancing the overall capacity of the dishwasher. Furthermore, the complete stainless-steel interior not only adds to the durability of the appliance but also contributes to better drying performance, as it helps retain heat during the drying cycle.

These KitchenAid dishwashers also come equipped with a high-efficiency spray arm that ensures even water distribution, reaching every corner for a comprehensive clean. The sleek design and innovative features make these models not only functional but also aesthetically pleasing, complementing any modern kitchen decor.

In terms of energy efficiency, these appliances are Energy Star certified, confirming they use less energy and water without sacrificing performance. This commitment to environmental sustainability reflects KitchenAid's dedication to quality and responsibility, making these models an excellent choice for eco-conscious consumers. Overall, the W10056407A, KUDE60FVPA, KUDS40FVPA, KUDS50FVPA, and KUDE70FVPA dishwashers provide a perfect blend of performance, convenience, and style.
Top Page Image Contents