Electrical Requirements

Product Damage

l Heavy duty door springs must be used with custom panels that weigh more than 4 pounds. Heavy duty door springs are attached to the right mounting bracket located behind the toe panel or can be ordered from your dealer or authorized parts distributor. Order Door Spring Kit, Part Number 9741247.

l Maximum door panel weight is 10 pounds.

Failure to follow these instructions could cause product damage.

Dishwasher door panel and access panel can be customized to match wood cabinets. It is recommended that a cabinet- maker cut the customized panel pieces because of the precise dimensions needed.

l Cut wood panels so that wood grain matches direction of grain in cabinets.

lFile or sand edges of wood panels.

l Apply moisture-resistant sealer on all sides of wood panels.

S/16” routed four sides for panel more than l/4” thick

Model A B C D

E;;;;:;;’

23-9116” 17-7116”

23-l l/16”

6-518”

23-9116” 18-13/16” 23-11116” 6-5/W

Dimensions for routing panel edges

Custom		panels		l/4” max.
more	than		l/4”
thick:	Route		outer
edge.
Custom		panels		+
less than		l/4”		5/16” min.
thick:	lnstajl
spacer	behind
panel.

panel

Side View

Electrical Shock Hazard

l Electrical ground is required on this appliance.

l If cold water pipe is interrupted by plastic, non-metallic gaskets or other insulating materials, Do Not use for grounding.

l Do Not ground to a gas supply pipe.

l Do Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in an electrical shock.

l Do Not modify the power supply cord plug.

l Do Not use an extension cord with this appliance.

l Check with a qualified electrician if you are in doubt as to whether this appliance is properly grounded.

It is the customer’s responsibility to: l Contact a qualified electrical

installer.

l Assure that the electrical supply is adequate and in conformance with the National Electrical Code, ANWNFPA 70 - latest edition*, and all local codes and ordinances.

Failure to follow these instructions could result in serious injury or death.

If codes permit and a separate ground- ing wire is used, it is recommended that a qualified electrician determine that the grounding path is adequate.

A single-phase, 11 j-volt, 60-Hz, AC-only,

15 or 20-ampere, fused electrical supply is required. Time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit, serving only this appliance, be provided.

This appliance may be connected with flexible armored or non-metallic sheathed copper cable (with grounding wire). A conduit connector must be installed at the junction box. Wire sizes (COPPER WIRE ONLY) must conform with the rating of the dishwasher.

-	A	-------	l\
-	A		l\
A.’	I		! ‘.
	7

Electrical connection

Direct wire connection

?%.Cut a 1” hole in the cabinet for the

electrical wiring to pass through. If this hole is cut in a wood cabinet, the hole should be sanded until smooth. If the hole is cut in a metal cabinet, the hole must be covered by a grommet (Part No. 302797). Run flexible cable from fused disconnect, circuit breaker or junction box through hole in cabinet. Cable should extend 24 inches minimum from back wall and easily connect to terminal box.

8Disconnect power supply.

After dishwasher is installed in ing, remove terminal box cover.

Install conduit connector to box.

Insert power cable through conduit

Using twist-on connectors, connect power supply cable to white

leads in terminal box. Connect black wire of power supply cable with black wire in terminal box.

grConnect grounding wire of power supply cable to grounding screw on dishwasher frame.

*Tighten conduit connector screws. Replace terminal box cover.

Flexible power supply cord connection

3-prong grounding-type wall receptacle

3-prong grounding ,

Local codes may permit the use of a U.L.- listed, flexible, three-conductor, 16- gauge, power supply cord terminated with a three-prong, grounding-type

plug.

It is recommended that cord kit, Part No. 675456, available from your KitchenAid dealer or parts supplier, be installed.

Follow Installation Instructions packaged with flexible power supply cord.

The flexible power supply cord used must:

lBe less than 6 feet in length.

l Meet National Electrical Code, ANSVNFPA 70 - latest edition*, and all local codes and ordinances.

l Not touch the dishwasher motor or lower portion of the dishwasher tub.

A grommet, Part No. 302797, must cover the hole cut in a metal cabinet for the flexible power supply cord.

To minimize possible shock hazard, the cord must be plugged into a mating three- prong, grounding-type wall receptacle grounded in accordance with National Electrical Code 70 - latest edition* and all local ordinances.

If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician.

The receptacle should be installed on the rear or side wall of the cabinet next to the dishwasher opening.

*Copies of the standard listed may be obtained from:

National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

Panel B

97415 14 specifications

The KitchenAid 97415 14 is a versatile kitchen appliance designed to enhance the culinary experience at home. This stand mixer stands out for its powerful performance, robust construction, and range of features that cater to both novice cooks and seasoned chefs.

One of the key highlights of the KitchenAid 97415 14 is its extensive mixing capacity. With a large 4.5-quart stainless steel bowl, it is ideal for handling recipes that require significant amounts of ingredients. Whether you are whipping cream, kneading dough, or mixing batter, the bowl's capacity allows for large batches, making it perfect for family gatherings or holiday baking.

This stand mixer is powered by a reliable 325-watt motor. The motor ensures consistent mixing results, tackling even the densest dough with ease. Coupled with a direct drive transmission, the mixer maintains speed and power, optimizing efficiency and performance during food preparation.

The KitchenAid 97415 14 offers a variety of speed settings, with ten different options to choose from. This allows users to customize their mixing process for different recipes, ensuring precise results every time. The slow stir speed is perfect for incorporating dry ingredients, while higher speeds provide the power needed for heavy mixtures.

Durability is another aspect where the KitchenAid 97415 14 shines. The mixer features a die-cast metal construction, providing stability during operation and extending its lifespan. Additionally, the iconic tilt-head design allows for easy access to the bowl and attachments, simplifying the process of adding ingredients or changing attachments.

Speaking of attachments, this stand mixer is compatible with a range of KitchenAid accessories, including pasta makers, food grinders, and vegetable slicers. This adaptability makes the KitchenAid 97415 14 a multifunctional tool, capable of performing various tasks beyond mixing.

In terms of user experience, the mixer is designed with ease of use in mind. The ergonomic handle on the bowl provides a comfortable grip during pouring, while the pouring shield helps to prevent messes. The mixer is available in a variety of colors, allowing users to choose a style that complements their kitchen decor.

Overall, the KitchenAid 97415 14 is a powerful and stylish stand mixer that combines performance with functionality. Its robust construction, versatile attachments, and user-friendly features make it an essential addition to any kitchen, empowering home cooks to explore their culinary creativity. Whether you’re baking bread, whipping meringue, or preparing delectable frostings, this mixer delivers exceptional results every time.