KitchenAid 3182048 installation instructions Downdraft Vent Must be Connected with Copper Wire

Page 10

Downdraft Vent

Electrical requirements

WARNING: To reduce the risk of fire, electric shock and injury to persons, the downdraft vent system must be installed with either the KitchenAid Model KPED890T exterior mounted motor unit or the KitchenAid Model KPID850T interior mounted motor unit. These units are marked to indicate their suitability with the downdraft vent system. Other motor units cannot be substituted.

IMPORTANT: Save Installation Instructions for electrical inspector’s use.

Electrical Shock Hazard

Electrically ground cooktop.

Failure to do so can result in death or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure the appliance is properly grounded.

Do Not have a fuse in the neutral or ground circuit.

El A 120-volt, 60-Hz, AC only electrical supply is required on a separate

’ 15-ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of the appliance specified on the model/serial rating plate located on the right side, above the wiring box on the downdraft burner box.

THE DOWNDRAFT VENT MUST BE CONNECTED WITH COPPER WIRE

ICIWire sizes and connections must 1 conform to the requirements of the

National Electrical Code, ANSI/NFPA 70 - latest edition**, and all local codes and ordinances. Wire sizes and connections must conform with the rating of the appliance.

Each appliance should be connected directly to the fused disconnect (or

ID.I circuit breaker) through flexible, armored or non-metallic sheathed, copper cable (with ground wire). Allow some slack in the cable so the downdraft vent can be moved if servicing is ever necessary.

El A U.L.-listed, l/2” conduit connector must be provided at the junction box.

El A wiring diagram is located in the literature package or on the inside cover of the downdraft vent wiring box.

Copies of the standards listed above may be obtained from:

**National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

Electrical connection

1.Cut a 1-l/2” hole in floor or side of cabinet for power supply wire. The hole cut for electrical wiring through a wood cabinet should be sanded until smooth. A grommet (Part No. 302797) must cover the hole cut for electrical wiring through a metal cabinet.

2.Run flexible armored or nonmetallic sheathed copper cable (with ground wire) from fused disconnect circuit breaker or junction box through the cabinet hole to downdraft vent location. A U.L.-listed conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box).

3.See installation steps to connect power supply to downdraft vent.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Create-a-Cooktop Read and save these instructionsWhat to do if YOU Smell GAS Before vou start Electric and Gas Single InstallationsProduct/cutout CooktopsCombinations All other dimensions remain the same for all cutoutsSpecial note for installations with gas cooktop Cutout to rear wallTools/Parts Tools and materials needed for installationParts supplied for installation Electric CooktopGrounded neutral Electrical connectionUngrounded neutral Now start Electric Cooktop and GrillWith cooktop and/or grill in kitchen Correspond to steps Downdraft Vent Must be Connected with Copper Wire Downdraft VentVenting requirements Recommended duct length for exterior mounted blower Exterior Mounted vent MotorRecommended standard fittings Now start . n n n ITT114I.II Downdraft Vent /contNumbers correspond to steps Downdraft Vent Blower box Steps Numbers correspond toGas supply requirements Sealed Gas CooktopGas conversion Electrical requirements Recommended ground methodAttach support brace to side \IL Numbers correspond to steps115.1 Electronic Ignition System initial lightingIf the cooktop, grill or downdraft vent does not operate Wiring diagramIf you need service If you need Assistance

3182048 specifications

The KitchenAid 3182048 is an essential component renowned for its durability and versatility, an integral part for any home chef equipped with KitchenAid appliances. A genuine part that ensures seamless compatibility with various KitchenAid stand mixers, this model represents the brand's commitment to quality and performance.

One of the main features of the KitchenAid 3182048 is its robust build quality. Made from high-grade materials, it guarantees longevity, resisting wear and tear even with regular, heavy use. This is critical for home cooks who rely on their kitchen tools day in and day out, assuring them that a replacement part won’t falter under pressure.

The KitchenAid 3182048 showcases an innovative design that enhances functionality. It is engineered to work effectively with various attachments, making it a versatile choice for preparing a wide range of dishes. Whether whipping cream, mixing dough, or blending ingredients, this component is designed to facilitate a smooth and efficient process.

This part also benefits from KitchenAid's renowned technological advancements. For instance, the compatibility with the brand's multi-purpose attachments allows users to transform their stand mixer into an even more valuable kitchen tool. Attachments like food grinders, pasta makers, and spiralizers can easily connect, expanding the culinary possibilities.

Furthermore, the KitchenAid 3182048 is easy to install and remove, making it user-friendly for both novice and experienced cooks alike. This simplicity encourages more experimentation in the kitchen, as users can quickly shift between tasks without hassle.

Another key characteristic of the KitchenAid 3182048 is its ease of maintenance. It is designed for quick cleaning, either by hand or in the dishwasher, ensuring that it remains hygienic and ready for use in minimal time. This focus on hygiene is particularly important for today's health-conscious consumers.

In conclusion, the KitchenAid 3182048 stands out as a robust and versatile component tailored for KitchenAid stand mixers. With its durable construction, innovative design, compatibility with numerous attachments, and ease of maintenance, it is an exemplary choice for anyone looking to enhance their kitchen experience. Whether you're a home chef or just someone who enjoys cooking occasionally, this part ensures that your KitchenAid mixer remains a dependable ally in culinary adventures.
Top Page Image Contents