KitchenAid 3182048 installation instructions Attach support brace to side

Page 21

To avoid scratching countertop, lift entire cooktop up from cutout when repositioning cooktop into countertop opening.

13.)

I I

Insert the cooktop into the countertop opening. Check that the front of the cooktop is parallel to the front edge of the countertop. Check that all required clearances are met. Use a pencil to mark a line along the rear of the cooktop on the countertop.

u4 Remove the

. cook-top from the cutout and place it

upside down on a protected surface.

Remove the paper backing from a small section of the

foam sealing strip. Place the strip l/8” from cooktop edge on the underside of the glass. Continue until foam strip completely outlines the edge of the cooktop.

If you are installing more than one appliance in the same cutout, you do not need to place a foam strip on the side that will be adjacent to another appliance.

Do Not use additional sealant around outer edge of cooktop(

E-l

 

 

 

 

Attach mounting

 

.

brackets to each

 

 

side

of the

burner

 

box with the 5/l 6” screws.

 

Do Not tighten

the

 

 

screws.

Turn

the

 

0

mounting

brackets

so

I

each is under the burner box.

If you are installing additional appliances in the same cutout, attach one mounting bracket to the right side of each additional appliance.

Insert the cooktop into the cutout and align it with the pencil line. Check that

cooktop is parallel to the front edge of the countertop. Lift the entire cooktop to make adjustments so the foam sealing strip can seal properly.

If you are installing only one appliance in cutout, go to Step 8.

If you are installing additional gas cooktops

in the same cutout, complete Steps 1, 2, 4, 5, 6 and 7 for each additional appliance.

If you are installing an electric cooktop or grill or a downdraft vent as an additional appliance, read and follow specific installation instructions for those products.

support brace

screws

1 . Attach support brace to side of the

Icooktop that will be adjacent to another appliance. Insert additional cook-top into the cutout and align with the pencil line used for first cooktop. Check that cooktop is parallel to the front edge of the countertop. Lift the entire cooktop to make adjustments so the foam sealing strip can seal properly.

Repeat for additional cooktops or grills.

Do Not over-tighten screws.

glass cooktop

countertop

\ I /

/

I

II-

2-1R” clamping screw

5M6” clamping

bracket screw

1 1

181. One cook-top in cutout: Rotate the

Imounting brackets away from the burner box. Do Not overtighten screws. Tighten the mounting brackets to the burner box. Insert the 2-l/2” clamping screws into the mounting brackets. Use a screwdriver to tighten the screws against the underside of the countertop. Remove the pencil outline from countertop.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Read and save these instructions Create-a-CooktopWhat to do if YOU Smell GAS Before vou start Product/cutout Single InstallationsElectric and Gas CooktopsSpecial note for installations with gas cooktop All other dimensions remain the same for all cutoutsCombinations Cutout to rear wallParts supplied for installation Tools and materials needed for installationTools/Parts Electric CooktopElectrical connection Grounded neutralUngrounded neutral Electric Cooktop and Grill Now startWith cooktop and/or grill in kitchen Correspond to steps Downdraft Vent Downdraft Vent Must be Connected with Copper WireVenting requirements Exterior Mounted vent Motor Recommended duct length for exterior mounted blowerRecommended standard fittings ITT Now start . n n nDowndraft Vent /cont 114I.IINumbers correspond to steps Downdraft Vent Blower box Numbers correspond to StepsSealed Gas Cooktop Gas supply requirementsGas conversion Recommended ground method Electrical requirementsAttach support brace to side Numbers correspond to steps \ILElectronic Ignition System initial lighting 115.1If you need service Wiring diagramIf the cooktop, grill or downdraft vent does not operate If you need Assistance

3182048 specifications

The KitchenAid 3182048 is an essential component renowned for its durability and versatility, an integral part for any home chef equipped with KitchenAid appliances. A genuine part that ensures seamless compatibility with various KitchenAid stand mixers, this model represents the brand's commitment to quality and performance.

One of the main features of the KitchenAid 3182048 is its robust build quality. Made from high-grade materials, it guarantees longevity, resisting wear and tear even with regular, heavy use. This is critical for home cooks who rely on their kitchen tools day in and day out, assuring them that a replacement part won’t falter under pressure.

The KitchenAid 3182048 showcases an innovative design that enhances functionality. It is engineered to work effectively with various attachments, making it a versatile choice for preparing a wide range of dishes. Whether whipping cream, mixing dough, or blending ingredients, this component is designed to facilitate a smooth and efficient process.

This part also benefits from KitchenAid's renowned technological advancements. For instance, the compatibility with the brand's multi-purpose attachments allows users to transform their stand mixer into an even more valuable kitchen tool. Attachments like food grinders, pasta makers, and spiralizers can easily connect, expanding the culinary possibilities.

Furthermore, the KitchenAid 3182048 is easy to install and remove, making it user-friendly for both novice and experienced cooks alike. This simplicity encourages more experimentation in the kitchen, as users can quickly shift between tasks without hassle.

Another key characteristic of the KitchenAid 3182048 is its ease of maintenance. It is designed for quick cleaning, either by hand or in the dishwasher, ensuring that it remains hygienic and ready for use in minimal time. This focus on hygiene is particularly important for today's health-conscious consumers.

In conclusion, the KitchenAid 3182048 stands out as a robust and versatile component tailored for KitchenAid stand mixers. With its durable construction, innovative design, compatibility with numerous attachments, and ease of maintenance, it is an exemplary choice for anyone looking to enhance their kitchen experience. Whether you're a home chef or just someone who enjoys cooking occasionally, this part ensures that your KitchenAid mixer remains a dependable ally in culinary adventures.
Top Page Image Contents