APOGEE Heat Pump
Descriptor | Address | Application | Description |
|
|
|
|
RM STPT MIN | 11 | 2281, 2283, | The minimum temperature setpoint in degrees that the |
|
| 2284, 2286, | controller can use from the setpoint dial. This overrides any |
|
| 2287 | temperature setpoint from the setpoint dial that falls below this |
|
|
| minimum. |
|
|
| Valid entry range: 48° to 95°F (9° to 35°C) |
|
|
|
|
RM STPT MAX | 12 | 2281, 2283, | The maximum temperature setpoint in degrees that the |
|
| 2284, 2286, | controller can use from the setpoint dial. This overrides any |
|
| 2287 | temperature setpoint from the setpoint dial that rises above this |
|
|
| maximum. |
|
|
| Valid entry range: 48° to 95°F (9° to 35°C) |
|
|
|
|
RM STPT DIAL | 13 | 2281, 2283, | The temperature setpoint in degrees from the room temperature |
|
| 2284, 2286, | sensor (not available on all temperature sensor models). This |
|
| 2287, 2299 | setpoint will be used for control in day mode (heating or cooling) |
|
|
| when enabled by STPT DIAL (Point 14). |
|
|
| Valid entry range: 48° to 95°F (9° to 35°C) |
STPT DIAL | 14 | 2281, 2283, | YES indicates that there is a room setpoint dial on the room |
|
| 2284, 2286, | temperature sensor and it is to be used as the temperature |
|
| 2287 | setpoint for control in day mode. NO indicates that the |
|
|
| appropriate preset setpoint (Points 6, 7, 8 or 9) will be used as |
|
|
| the temperature setpoint for control in day heating or cooling |
|
|
| mode. |
|
|
| Valid input: YES or NO |
AUX TEMP | 15 | 2299 | Actual reading from a 100K ohm thermistor connected to the |
|
|
| controller's Al 3 input. When a thermistor is connected at Al 3, |
|
|
| DI 3 is not available. Refer to Dl 3 (Point 25). |
DISCH TEMP | 15 | 2281, 2284, | Actual reading from a 100K ohm thermistor connected to the |
|
| 2287 | controller's AI 3 input. When a thermistor is connected at Al 3, |
|
|
| DI 3 is not available. Refer to DI 3 (Point 25). |
MA TEMP | 15 | 2283, 2286 | Actual reading from a 100K ohm thermistor connected to the |
|
|
| controller's Al 3 input. When a thermistor is connected at Al 3, |
|
|
| DI 3 is not available. Refer to DI 3 (Point 25). |
|
|
|
|
1 VLV HTGCLG | 16 | 2281, 2283 | YES indicates that there is one valve controlling one coil which |
|
|
| may have hot or chilled water in it. |
|
|
| indicates any other hardware setup. |
|
|
| Valid input: YES or NO |
|
|
|
|
FBP.MODVALVE | 17 | 2281, 2283, | FBP indicates that both heating and cooling will be modulated |
|
| 2284, 2286 | with a |
|
|
| configurations. |
|
|
| Valid input: FBP or VALVE |
|
|
|
|
WALL SWITCH | 18 | 2281, 2283, | YES indicates that the controller is to monitor the status of a |
|
| 2284, 2286, | wall switch that is connected to DI 2. NO indicates that the |
|
| 2287, 2299 | controller will not monitor the status of a wall switch, even if one |
|
|
| is connected. |
|
|
| Valid input: YES or NO |
DI OVRD SW | 19 | 2281, 2283, | Actual indication of the status of the override switch (not |
|
| 2284, 2286, | physically available on all temperature sensor models) at the |
|
| 2287, 2299 | room temperature sensor. ON indicates that the switch is being |
|
|
| pressed. OFF indicates that the switch is released. |
|
|
| Valid input: ON or OFF |
24 | Siemens Building Technologies, Inc. |