Hotpoint 25 Plug in the Refrigerator, Start the Icemaker, Important Notes, Tools YOU will Need

Page 16

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

11PLUG IN THE REFRIGERATOR

Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.

START THE ICEMAKER

Power switch models – Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically if the icemaker power switch is in the I (on) position, and the green light will come on.

Power

SwitchIcemaker

START THE ICEMAKER (CONT.)

Feeler arm models – Move the feeler arm to the ON (down) position. The icemaker will not begin to operate until it reaches its operating temperature of (15 F) (-9 C) or below. It will begin operation automatically if the icemaker feeler arm is in the ON (down) position.

Feeler Arm in the

STOP (up) position

Feeler Arm in the ON (down) position

Feeler arm model

NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

Green Power

Feeler Arm

Light

 

Power switch model

REVERSING THE DOOR SWING

IMPORTANT NOTES

When reversing the door swing:

Read the instructions all the way through before starting.

Handle parts carefully to avoid scratching paint.

Set screws down by their related parts to avoid using them in the wrong places.

Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

the right side to the left side—if you ever want to change the hinges back to the right side, follow these same instructions and reverse all references to left and right.

Unplug the refrigerator from its electrical outlet.

Empty all door shelves, including the dairy compartment.

TOOLS YOU WILL NEED

Phillips screwdriver

5/16Head socket driver 3/4Head socket driver (a 6-point socket is recommended)

Putty knife or thin-blade screwdriver

Masking tape

16

Image 16
Contents Refrigerators Write the model and serial numbers here Model # Serial #Off setting RefrigerantsHOW to Connect Electricity Instructions Troubleshooting TipsAbout the controls on the refrigerator Touch pad controlsLocking the Controls on some models To lock the controlsAbout the shelves and bins Rearranging the ShelvesSpillproof Shelves on some models To removeAdjustable Bins on the Door Non-Adjustable Shelves on the DoorSlide-Out Spillproof Shelf on some models Freezer Tilt Out Bin on some modelsAbout the additional features About the crispers and pansIcemaker Accessory Kit About crisper removalAbout the automatic icemaker Crisper RemovalCare and cleaning of the refrigerator Replacing the light bulbs Refrigerator CompartmentFreezer Compartment Light on some models Freezer Compartment Dome Light on some modelsWater Supply to the Icemaker Refrigerator LocationClearances RollersBefore YOU Begin What YOU will NeedChoose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Fasten the Shutoff Valve Connect the Tubing to the ValveTighten the Pipe Clamp Route the TubingConnect the Tubing to the Refrigerator Turn the Water on AT the Shutoff ValvePlug in the Refrigerator Start the IcemakerImportant Notes Tools YOU will NeedRemove the Refrigerator Door Remove the Freezer DoorTransfer TOP Hinge to the Left Transfer Door Stops Transfer Bottom Hinge Bracket to the LeftTransfer Refrigerator Door Handle to the Right Long HandleRehang the Refrigerator Door Rehang the Freezer DoorNormal operating sounds HummmBefore you call for service… Instructions OperatingSee Care and cleaning Ice cubes haveOdor/taste No ice cubeWe Will Replace What Is Not CoveredOne Year Page Troubleshooting Tips Page Schedule Service Parts and AccessoriesConsumer Support Hotpoint Website Real Life Design Studio
Related manuals
Manual 64 pages 18.54 Kb