Whirlpool RJH 3330-1 Thick Sheet Rock, Screw, No. Io, Hollow Wall Anchor Bolt

Page 3

-

--; THICK

SHEET ROCK

2s’

SCREW, NO. IO

<.

U

HOLLOW WALL

ANCHOR BOLT

Figure 5

9.Remove all 4 screws from the anchor bolts.

10.Attach hanging bracket to the wall with the four screws taken from the anchor bolts. Tighten the screws in the anchor bolts until the anchor bolts are completely set.

11.Install four remaining ‘/4” dia. lag bolts through the hanging bracket and into the two studs.

CAUTION: Do not overtighten the lag screws. If they are overtightened, the bracket may pull into the wall material which will not allow the shelf to slide into place properly.

12.The hole in the bottom of the cabinet (for the duct provided with the hood) should be cut as shown in Figure 6 (15%” long by 1%” deep). Hole must be cut to back wall. Make sure to center the hole within the 30” allotted space.

14.Hang the shelf hood on the hanging bracket. (See Figure 10). To be sure theshelf hood hanging angle is completely engaged in the hanging bracket, measure from the top of the shelf hood to the top of the hanging bracket. This distance should be l-7/16” on both ends.

CAUTION: Do not continue until both ends measure l-7/16”. If the hanging angle is not fully engaged in the hanging bracket, the Microshelf Hood will not be level and the hood may become dislodged from the hanging bracket. This could cause damage.

15.Complete the duct work by:

A.Fit the duct provided with the Microshelf Hood on to the vent outlet of the Microshelf hood.

B.Mark and drill (2) %” dia. holes (1 each side) to fasten the thin duct provided with the hood to the back wall. See Figure 7.

C.Use 2 #8 x VI” long screws provided with the unit to fasten the narrow thin duct to the shelf. See Figure 7.

D.Next install the transition adaptor to the thin duct.

This transition adaptor will accept 3%” x 10” duct.

E.Complete the 3%” x 10” duct (or

equivalent) to the outside using the guidelines listed under venting requirements.

LHANGING BRACKET

Figure 6

13.Rough wire the electrical supply to the area shown in Figure 3.

Page 3

B. Connect the electrical supply:

It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that

the electrical installation is adequate and is in conformance with the National Electrical Code and local codes and ordinances.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents YLrlmml STUD, Consult a Local Building Contractor for Help II. Vented InstallationThick Sheet Rock SCREW, NO. IOHollow Wall Anchor Bolt Installing and Leveling the Microwave Oven Screw Removed fromLifting ABILITY. WE Recommend Assistance Care of Filters LightsCare of Exterior Surfaces ~irlpool

RJH 3330-1 specifications

The Whirlpool RJH 3330-1 is a sophisticated freestanding refrigerator that embodies modern design and advanced technology, making it a standout choice for contemporary kitchens. With a user-centric approach, this model ensures a perfect balance between functionality and aesthetics.

One of the main features of the Whirlpool RJH 3330-1 is its spacious interior. With a total capacity of approximately 336 liters, it provides ample space for storing groceries, beverages, and leftovers. The refrigerator compartment is designed with adjustable shelves, allowing users to customize storage according to their needs. The spacious freezer section also provides ample room for frozen goods, making meal planning and preparation efficient and convenient.

This refrigerator boasts several advanced technologies that enhance its performance. The No Frost system is a notable feature, which eliminates the need for manual defrosting. This technology prevents ice buildup, ensuring optimal airflow and temperature consistency throughout the refrigerator. As a result, food remains fresh for longer periods, ultimately reducing food waste.

Energy efficiency is another key characteristic of the Whirlpool RJH 3330-1. With an impressive energy rating, this model not only helps to lower electricity bills but also contributes positively to the environment. The use of LED lighting further enhances energy savings while providing bright and clear illumination of the interior.

In terms of design, the Whirlpool RJH 3330-1 features a sleek and modern exterior that blends seamlessly with various kitchen decors. The stainless steel finish offers durability and ease of cleaning, while the minimalist handles enhance the appliance's aesthetic appeal.

The cooling system is equipped with advanced temperature controls, allowing users to set optimal temperatures for different food types. This ensures that perishables remain at their best, extending the shelf life of fruits and vegetables.

In conclusion, the Whirlpool RJH 3330-1 combines practicality, efficiency, and style. Its spacious design, energy-saving technologies, and user-friendly features make it an excellent addition to any household. Whether you are a busy family or an individual who values convenience, this refrigerator offers solutions that cater to your modern lifestyle, all while keeping food fresh and organized.
Top Page Image Contents