Whirlpool GZ8330 Make electrical connection, Vented installations, Non-vented installations

Page 6

keyhole slot

front of hood

13.Lift the range hood up under cabinet and determine final position. Mark on the underside of cabinet the location of the four keyhole mounting slots. Set range hood aside on a protected surface.

drill pilot hole

14.Use 1/8" (or 3 mm) drill bit and drill 4 pilot holes as shown.

1/4"

(6.4 mm)

15.Remove the 4 hood mounting screws from the parts bag and install in pilot holes. Leave screw heads away from filler strips or cabinet bottom about 1/4" (6.4 cm)

16.If using direct wiring, make sure power is disconnected, and pull about 12" (30 cm) of wire through wall or cabinet and into opening.

17.Lift range hood into final position, feeding electrical wire through wiring opening. Position the range hood so that the large end of the keyhole slots are over the screws.Then push the hood toward the wall so that the screws are in the neck of the slots.Tighten mounting screws to cabinet, making sure mounting screws are in narrow neck of slots. Make sure that damper

Make electrical connection

WARNING

Electrical Shock Hazard

Disconnect power before making electrical connections.

Connect ground wire to green ground screw in terminal box.

Failure to do so can result in death or electrical shock.

white

black

black

green

 

locknut

green or bare

electrical

connector

ground wire

 

19.Make electrical connections. Install locknut on electrical connector and tighten securely. Connect white to white and black to black wires using twist-on connectors. Connect green or bare ground wire to the green ground screw.

Using a U.L.-listed power supply cord-connection kit (U.S. only):

Follow Power Cord Kit instructions for connecting wiring.

blower

blower

discharge

discharge

horizontal vent

vertical vent

22.Reinstall blower.

Vented installations:

Reinstall blower. Do not grasp blower by blower wheels. Position blower so that blower discharge lines up with damper/vent connector and slip rods into mounting brackets on blower assembly. Tighten knurled nuts securely and reconnect blower plug.

Non-vented installations:

front holes

blower discharge

Reinstall blower. Do not grasp blower by blower wheels. Move mounting rods to front holes in hood support channels. Position blower so that blower discharge lines up with louvered opening on hood front.

Slip rods into mounting brackets and tighten knurled nuts securely. Reconnect blower plug.

louver cover

Remove louver cover on control panel. Pry cover off with screwdriver or knife.

23.Reinstall bottom cover (see Step 6).

blade, if used, rotates up and down freely.

18.Connect ventwork to hood. Seal joints with duct tape to make the secure and air tight.

20.Replace wiring box cover and screws. Make sure that wires are not pinched between cover and hood.

21.Install two 75 watt max. bulbs, or one 75 watt and one 25 watt bulb for night-light use. Install 25 watt bulb in right-hand socket.

To get the most efficient use from your new range hood, read the “Use and Care Information” section.

Keep your Whirlpool

Installation Instructions and Use and Care Guide close to range hood for easy reference.

6

Image 6
Contents Table of Contents Quick ReferenceBefore you start Tools and materials needed for installationMobile home installation Parts suppliedVertical roof venting Product dimensionsVenting requirements Recommended vent lengthRecommended standard fittings Now start4 x 10 8.3 x 25.4 cm vent system Cm vent system4 x 10 8.3 x 25.4 cm Prepare and install the hoodFor vented installations, go to a Vent systemNon-vented installations Follow Power Cord Kit instructions for connecting wiringVented installations Make electrical connectionOperation Blower SpeedBlower on Aluminum mesh filters Whirlpool Range Hood WarrantyCleaning Light lensRequesting Assistance or Service Our consultants provide assistance withIf you need service Listed in Check OperationConsultation rapide Table des matièresSérie GZ8330 Série GZ8336 Outillage et matériel nécessaires pour l’installation Installation dans une résidence mobileAvant de Commencer Dimensions du produit Consulter un électricien qualifiéLe système doit décharger l’air à l’extérieur Longueur maximale Préparation de l’emplacement de l’installationDécharge horizontale, à Travers le mur 70 piDe la hotte Et installationPréparation Conduit d’évacuationInstallations avec conduit de décharge Installations avec recyclageInstallation avec conduit de décharge Installation avec recyclageSpeed Vitesse du ventilateur Utilisation et entretienFonctionnement On Mise en marche du ventilateurNettoyage Garantie Whirlpool Hotte d’extractionPour plus d’assistance Si vous avez besoin d’assistance ou de service au CanadaSi vous avez besoin de service « Dépannage »

GZ8330, GZ8336 specifications

The Whirlpool GZ8336 and GZ8330 are two innovative models from a brand renowned for its commitment to quality and technology in home appliances. Both models are designed to enhance user convenience while delivering outstanding performance.

One of the standout features of the Whirlpool GZ8336 is its impressive capacity. With a spacious interior, it easily accommodates large quantities of food, making meal prep and storage more efficient for families and individuals alike. The GZ8330, while slightly smaller, maintains a similar level of efficiency and usability, making it an ideal choice for those with limited space but still requiring reliable performance.

Both models are equipped with advanced temperature control technology. This ensures that food items are preserved at optimal temperatures, thereby extending shelf life and maintaining freshness. The precise thermostat allows users to set and maintain their desired temperatures accurately. This is particularly beneficial for users looking to store a variety of items, from delicate produce to frozen meats.

Energy efficiency is another crucial characteristic of the GZ8336 and GZ8330 models. Whirlpool has incorporated energy-saving technologies that exceed industry standards. This not only helps reduce utility bills but also minimizes the environmental impact, aligning with modern sustainable living practices.

In terms of design, both models feature sleek exteriors that can seamlessly blend with various kitchen styles. The interiors are thoughtfully designed for maximum usability, with adjustable shelves and organized storage compartments that make it easy to access items.

Both units also incorporate innovative cooling technologies that minimize frost buildup and ensure even cooling throughout. This technology is particularly advantageous in maintaining consistent temperatures across different sections of the fridge or freezer, thus further enhancing food preservation.

Moreover, user-friendly controls and features such as quick access storage compartments make these models highly functional. The GZ8336 and GZ8330 are also backed by Whirlpool's reliable customer service, ensuring peace of mind for users. In summary, the Whirlpool GZ8336 and GZ8330 offer a combination of capacity, efficiency, and advanced technologies, making them excellent choices for any modern kitchen.