Hotpoint FDYB 11011, FDYB 10011 Installation, Positioning and levelling, Electrical Connection

Page 5

Installation

If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back.

Positioning and levelling

1.Remove the appliance from all packaging and check that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed any further with the installation process.

2.Check the dishwasher by placing it so that its sides or back panel are in contact with the adjacent cabinets or even with

the wall. This appliance can also be recessed under a single worktop* (see the Assembly instruction sheet).

3.Position the dishwasher on a level and sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted until it reaches a horizontal position. If the appliance is levelled correctly, it will be more stable and much less likely to move or cause vibrations and noise while it is operating.

4*. Adjust the height of the rear foot from the front of the appliance on the central lower part of the dishwasher, turning a hexagonal spanner (red color) with an opening of 8 mm in a clockwise direction to increase the height or in an anticlockwise direction to decrease the height.

The dishwasher meets the requirements set out by the regulations in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by a trained and authorised technician: Repairs carried out by unaithorised persons will invalidate the guarantee, as well as posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component or from the use of non-original spare parts.

Electrical Connection

Before inserting the plug into the electrical socket, make sure that:

the socket is earthed and complies with current regulations;

the socket can withstand the maximum load of the appliance, which is indicated on the data plate located on the inside of the door (see Description of the appliance);

the power supply voltage falls within the values indicated on the data plate on the inside of the door;

the socket is compatible with the plug of the appliance. If this is not the case, ask an authorised technician to replace the plug (see After Sales Service); do not use extension cables or multiple sockets.

Once the appliance has been installed, the power supply cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

GB

If the power supply cable is damaged, it must be replaced by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards. (See After Sales Service)

This appliance must be earthed.

Fuses:your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only those rated at 13A and ASTA approved to BS1362 should be used. If you lose the fuse cover, a replacement may be obtained from your local authorised Service Centre or Electrical company. Correct replacement is identified by colour coding or the marking on base of plug.

DO NOT use the plug unless the fuse cover is fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

To avoid a shock hazard DO NOT insert the discarded plug into a socket anywhere else.

Wires in the mains lead are coloured accordance with the following code:

Green/Yellow -

Earth

 

Blue

-

Neutral

Brown

-

Live

If you change the plug, the colour of the wires in the mains lead may not correspond with the terminal markings in the plug, which if not coloured, could be:

EARTH ‘E’

or

 

 

 

NEUTRAL

‘N’

LIVE

‘L’

Changing the Mains Lead

A lead can be ordered from Hotpoint Service

UK: 08709 066 066 or

Republic of Ireland: 1850 302 220

-If you have damaged the existing lead or require a longer one a charge will be made. It is strongly advised that this work is carried out by a qualified electrician.

-If the domestic wiring includes a residual current-operated circuit breaker, ensure that it conforms to the latest regulations.

The dishwasher must not be connected to the electricity supply while installation is being carried out.

-This appliance should only be connected to a 230/240V AC source, via a properly installed earthed socket.

-Use the dishwasher solely in a domestic environment.

-DO NOT stand or place heavy objects on the door when it is open, this could damage the door or cause the appliance to tip forward.

5

Image 5
Contents Instructions for use ContentsHotpoint Product FicheGeneral safety Precautions and safety adviceDisposal of old electrical appliances Saving energy and respecting the environmentRecycling & Disposal Information Electrical Connection InstallationPositioning and levelling Connecting the water inlet hose Connecting the water suppliesSink Waste System Anti-condensation stripAnti-flooding protection Advice regarding the first wash cycleControl panel Description of the applianceLower rack Loading the racksCutlery basket Upper rackAdjusting the height of the upper rack Tip-up compartments with adjustable positionCutlery tray Unsuitable crockeryMeasuring out the detergent Start-up and useStarting the dishwasher Wash Cycle Wash cyclesSetting the water hardness Rinse-aid dispenser settingRinse aid and refined salt Measuring out the rinse aidCare and maintenance Problem Possible causes / Solutions TroubleshootingAfter Sales Service After Sales ServiceParts and Accessories Essential Contact InformationMonths Parts and Labour Guarantee GuaranteeYear Parts Guarantee Extended GuaranteesPage Page 195113144.03

FDYB 11011, FDYB 10011 specifications

The Hotpoint FDYB 10011 and FDYB 11011 are innovative dishwashers designed to enhance the efficiency of modern kitchens. These models are part of Hotpoint's commitment to combining style, functionality, and energy efficiency in their appliance lineup.

Both the FDYB 10011 and FDYB 11011 come equipped with several main features that make them stand out in the crowded dishwasher market. One of the key attributes of these models is their spacious interior, which can accommodate up to 13 place settings. This means that families or those who entertain frequently will find these dishwashers particularly advantageous, as they can handle larger loads without the need for multiple cycles.

The energy efficiency of the FDYB 10011 and FDYB 11011 is another highlight, as both models boast impressive energy ratings, making them cost-effective choices for consumers. These dishwashers are designed to use less water and electricity, reducing the environmental impact while still delivering powerful cleaning performance.

In terms of technology, both models feature the innovative "Eco Technology," which optimizes water consumption and energy use during wash cycles. This means less waste without compromising cleaning effectiveness. Additionally, the "Hygiene" program is a notable inclusion that uses higher temperature settings to provide a deeper clean, killing up to 99.9% of bacteria on dishes – a significant feature for households with young children or those concerned about hygiene.

The "Intensive" wash program is another advantage, perfect for heavily soiled pots and pans. It ensures that even the toughest stains are dealt with efficiently, making post-meal cleanup easier than ever.

The design of the FDYB 10011 and FDYB 11011 is sleek and modern, fitting seamlessly into any kitchen decor. The control panel is user-friendly, featuring intuitive touch controls that make program selection straightforward.

In summary, the Hotpoint FDYB 10011 and FDYB 11011 dishwashers offer a blend of spaciousness, energy efficiency, advanced technology, and user-friendly design. With their powerful cleaning capabilities and innovative features, they cater to the needs of busy households, ensuring that dishwashing becomes a hassle-free task.