Hotpoint HDA6009 warranty HOW to Operate Your Dishwasher, BLatchthedo’r

Page 4

HOW TO OPERATE YOUR DISHWASHER

STEP 1. Load your dishwasher with dishes, silverware, pots, pans, bowls, etc., according to the Loading section.

STEP 2. Add detergent to the detergent dispenser. Make sure the Cycle Indicator Dial is at OFF position before adding detergent. (See Detergent Guide).

Use rinse aid agent to help prevent spotting. Occasionally check to insure that rinse agent container is at least half full. (See How to Use a Rinse Agent section).

STEP 3. Select drying option.

I

HEATED DRY. Turns the

H;\T;D ENERGY

SAVER

drying heater on for fast drying.

 

ENERGY SAVER. Turns the drying

m

 

heater off to save energy. The dishes

M

will dry naturally over a longer period such as overnight.

If you need your dishes sooner, open the dishwasher door after the cycle is complete to reduce the natural drying time.

Use of this option reduces the electrical energy used by this model approximately 10% for the NORMAL WASH cycle.

STEP 4. WATER HEAT energy option.

The wash cycle will be extended for 9 minutes while the dishwasher heats the water for good washing

For POTS & PANS, NORMAL WASH and WATER SAVER cycles:

a. Push selected cycle button.

bLatchthedo(’r

Cycle

mI .,.1. ,.1,.1.,

. Slowly turn

Indic;tor Dial to ON

position to start the

 

washing

 

cycle. You will hear

 

 

 

the motor start. There

ON .

 

 

is a time delay between

OFF (*

)

,,,

 

RINSE

the start-up and the water

 

& HOLD

 

d~lng e

 

fill so you will not hear

 

. P1ATEW4RMER

ff,,

any wash action right away.

 

 

 

 

 

 

 

 

For RINSE & HOLD cycle: a. Be sure door is unlatched.

b. Select ENERGY SAVER drying option.

c. Slowly turn the Cycle [ndicator Dial to the RINSE & HOLD position.

d. Latch the door to start the cycle.

For PI. ATE WARMER cycle:

and drying. The entering water must be at least

120°F. See How to Test the Water Temperature section.

STEP 5. Select the wash cycle and start the dishwasher. (See Cycle Selection Hints).

If your dishwasher drains into a food waste disposer, operate the disposer until it is empty before starting the dishwasher.

a. Load clean plates and dishes to be warmed.

b. Select HEATED DRY drying option.

c. Leave the door unlatched.

d. Slowly turn the Cycle Indicator Dial clockwise

washin.

To obtain the benefits of a complete cycle, be careful that you do not turn the dial any farther than necessary to start the dishwasher.

to the PLATE WARMER position.

e. Latch the door to start the cycle.

4

Image 4
Contents Dkhwmher ~ YOU Need Service Save time and money. Before you request serviceHelp US Help YOU If you received Damaged dishwasherSave These Instructions To minimize the possibility of inju~HOW to Operate Your Dishwasher BLatchthedo’rWhat Happens in Each Cycle Cycle Selection HintsGood dishwashing starts with HOT water How to Use a Rinse Agent How to Test Water TemperatureHow to Choose and Use the Right Detergent Detergent Usage Guide powder or liquid How to Prepare the Dishes for WashingUse no detergent HOW to Load Your Dishwasher HOW to Load the TOP RackShelf Up HOW to Load T‘HE Bottom WCKShelf Down HOW to Load Tm Bottom WCK PrecautionForget a dish? Here’s when you can add it Subhead that goes all the way acrossCAm Am Cleaning Built-in Dishwashers Often Use an Air Gap. Keep It CleanHow to change the door panel USE this Problem Solver QUESTIONS?Glassware To remove stubborn spots and film from glassware~ Problem Solver OUT of the TUBOrder Form ~ Kit GPFHotpoint Wdll Be There Warranty