Hotpoint Aquarius FDW20 manual Levelling, Height Adjustment, Standpipe, Anti-flooding protection

Page 5

D ISHWASHER

Installation

Choose where you want to install your dishwasher, you can place it so that its sides or back panel are side by side with furniture or up against the wall. The dishwasher is providedwithwatersupplyanddrain hoses, which can be directed towards the left or right to facilitate appropriateinstallation.

Levelling.

Once the appliance is positioned, adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal. Make sure that it is not inclined more than 2 degrees. If the applianceislevel,itwill helpensure its correct operation.

Height Adjustment

Insert the appliance into the cutout andthenadjusttheheightusingthe screws located on the front bottom

Connect to the Water Supply...

-For your dishwasher to operate correctly it requires water pressures in the range of 6-150 psi (100-1000KPa). Most cold water supplies will be in this range. NOTE:lowwaterpressurewilllead to excessively long fill times or no fill.

-Ensurethatthenewhosesupplied is connected and the old hose is disposed of safely.

-Ensure the fill hose is only fitted to the cold water supply. DO NOT overtighten the hose connector, hand tight is sufficient.

-Ensure the fill hose is not kinked.

-Tap connections (if applicable): A range of adaptors are available to suit your tap.

-DO NOT connect the dishwasher to a single outlet instantaneous water heater or an electric heater.

Drain hose connection. WARNING: Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains.

IMPORTANT: For the correct operation of your dishwasher, it is essentialtocomplywiththefollowing information:-

Standpipe:

Ensure that the hose is not pushed too far down the standpipe.

If the end of your drain hose is fitted with‘retainingflaps’,ensuretheyare insertedfullyintothestandpipe. This will prevent the pipe from jumping out during installation and use.

SinkWasteSystem: For under sink drainage:

Before connecting the drain hose, remove any internal restrictions - This will prevent a build up of debris which could cause a blockage.

Remove any restrictions from the waste spigot and ensure that the sealingbungisremoved.Thehose should be routed, such that it is raised to a minimum height of 800mm(31/2”).

NOTE: Ensure the sink outlet pipe has a minimum diamtere of 32mm.

part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively.

Anti-flooding protection

Your dishwasher is provided with aspecialsystemwhichblocksthe water supply in the event of leaks insidetheappliance.

Cold water connection. Connect the cold water supply hose, If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher.

DO NOT position the standpipe near an electrical outlet. ENSURE that the drain hose is not kinked and it is routed as shown in thediagram.

The standpipe should have a bore of at least 38mm (11/2”). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your householdsink.

It MUST NOT be connected to a surface water drain.

1.Untie the end of the GREY drainage hose from the rear of the appliance.

2.Reposition the ‘Hooked End Support’ as required along the GREY drainage hose.

3.If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug.

Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Instructions for Installation and Use Contents Fuses Electrical ConnectionMains plug must be easily accessible after installation For your SafetyLevelling Height AdjustmentStandpipe Anti-flooding protectionIshwasher Getting to know your Dishwasher ON-OFF Indicator lightControls ON-OFF ButtonFirst of all How to use your DishwasherModifying a wash cycle in progress Cycle endPRE-WASH Programme ChartAdjusting the water softener To where you live. If the waterWhen to add salt Water hardness varies accordingAdding detergent Before Using your DishwasherIf it wont close Adding rinse aidLoading your Dishwasher How to adjust the upper basketWhat goes into the upper basket? Load examplesLoading the Rinse Aid Loading the detergentCleaning the spray arms Care and CleaningUnplug the appliance After every washResolving minor problems yourself TroubleshootingIshwasher Ishwasher Extended Warranties Repair Service and Information Help DeskGenuine Parts and AccessoriesUK 08709 077 Guarantee terms and conditions Satisfaction guaranteed or your money back19504431805 Repair Service and Information DeskGenuine Parts and Accessories

Aquarius FDW20 specifications

The Hotpoint Aquarius FDW20 is a notable addition to the world of domestic dishwashing, combining efficiency, innovation, and user-friendly features. This dishwasher is designed to tackle the rigors of everyday life, making it an ideal choice for families and individuals alike.

One of the standout features of the Hotpoint Aquarius FDW20 is its energy efficiency. With an A+ energy rating, it helps users save on electricity bills while also being environmentally conscious. The machine’s design ensures that water and energy consumption are minimized without compromising cleaning performance.

Equipped with a 12-place setting capacity, the FDW20 is spacious enough to handle the dishes of an average household. The internal layout is intelligently designed with adjustable racks, allowing for customization based on the load. This ensures that both large pots and small cups can be accommodated without issue. The top basket is also adaptable, which enhances its flexibility when loading various types of dishes.

The Hotpoint Aquarius FDW20 features several wash programs to suit different needs. The quick wash cycle is particularly appealing for those in a hurry, providing a thorough clean in just 30 minutes. Other programs include eco-friendly options that prioritize water and energy conservation, as well as intensive cycles for heavily soiled items. This versatility makes it suitable for any dishwashing challenge.

Another significant characteristic of the FDW20 is its innovative technologies. The device includes a water sensor that automatically adjusts water hardness, ensuring that every wash is optimized for the best results. Moreover, the built-in turbo drying system aids in effectively drying the dishes, reducing the need for towel drying and saving users time.

Beyond performance, the Hotpoint Aquarius FDW20 prioritizes user convenience. The electronic controls are straightforward and intuitive, enabling error-free operation. The presence of a delayed start option allows users to set the machine to run at their convenience, optimizing energy usage further.

In summary, the Hotpoint Aquarius FDW20 is a robust and efficient dishwasher that epitomizes modern kitchen convenience. With its energy efficiency, flexible loading options, varied programs, and advanced technology, it promises to make dishwashing less of a chore and more of a seamless task in daily life. Whether you're a busy family or an individual, this dishwasher is built to meet a variety of cleaning needs while delivering reliability and satisfaction.
Top Page Image Contents