Hotpoint BFI62 manual Levelling, Standpipe, Height Adjustment

Page 7

Installation

D ISHWASHER

Choose where you want to install your dishwasher, you can place it so that its sides or back panel are side by side with furniture or up against the wall. The dishwasher is providedwithwatersupplyanddrain hoses, which can be directed towards the left or right to facilitate appropriateinstallation.

Levelling.

Once the appliance is positioned, adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal. Make sure that it is not inclined more than 2 degrees. If the applianceislevel,itwill helpensure its correct operation.

Cold water connection. Connect the cold water supply hose, inserting the small filter supplied with the dishwasher and makingsurethatitisfastenedtightly in place (see figure 2). If the water hoses are new or have been out of use for an extended period of time, let the water run to make sure it is clear and free of impurities before making the connection. If this precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher.

Drain hose connection. WARNING: Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains.

IMPORTANT: For the correct operation of your dishwasher, it is essentialtocomplywiththefollowing information:-

Standpipe:

Ensure that the hose is not pushed too far down the standpipe.

If the end of your drain hose is fitted with‘retainingflaps’,ensuretheyare insertedfullyintothestandpipe. This will prevent the pipe from jumping out during installation and use.

Sink Waste System: For under sink drainage:

Before connecting the drain hose, remove any internal restrictions - This will prevent a build up of debris which could cause a blockage.

Remove any restrictions from the waste spigot and ensure that the sealingbungisremoved.Thehose should be routed, such that it is raised to a minimum height of 800mm(31/2”).

Height Adjustment

Insert the appliance into the cutout andthenadjusttheheightusingthe screws located on the front bottom part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively.

A

Fig.2

DO NOT position the standpipe near an electrical outlet. ENSURE that the drain hose is not kinked and it is routed as shown in thediagram.

The standpipe should have a bore of at least 38mm (11/2”). It should be installed as shown, have a trap fitted and must discharge into the same drain system as your householdsink.

It MUST NOT be connected to a surface water drain.

NOTE: Ensure the sink outlet pipe has a minimum diamtere of 32mm.

1.Untie the end of the GREY drainage hose from the rear of the appliance.

2.Reposition the ‘Hooked End Support’ as required along the GREY drainage hose.

3.If fitting an under sink waste disposal unit, cut out the membrane, bung or blanking plug.

4.Attach the GREY drainage hose to the under sink waste disposal unit securely, using the clip and rubber tube supplied.

Ensure the drain hose is securely attached, to prevent it coming away while the machine is in use and causing a flood.

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Instructions for Installation and Use Page Contents Page Fuses Electrical ConnectionDONOTremovetheratingplate For your SafetyLevelling Height AdjustmentStandpipe Controls ON-OFF Indicator lightCycle indicator light Getting to know your DishwasherCycle end How to use your DishwasherFirst of all Modifying a wash cycle in progressZdvk Programme ChartAdjusting the water softener Before Using your DishwasherFilling the salt container 25 gr Cleaner DishesAdding detergent If it wont closeWhat goes into the upper basket? How to adjust the upper basketLoading your Dishwasher What goes into the lower basket?Unplug the appliance Care and CleaningCleaning the spray arms Cleaning the Water Inlet FilterResolving minor problems yourself TroubleshootingRinse aid DetergentLoading the detergent See table at the endGenuine Parts and AccessoriesUK 08709 077 Repair Service and Information Help DeskExtended Warranties Guarantee terms and conditions Satisfaction guaranteed or your money backPage 195.036.720.00 Repair Service and Information DeskGenuine Parts and Accessories January 2003 Part no. FP149

BFI62 specifications

The Hotpoint BFI62 is a stylish and versatile built-in oven that combines modern technology with user-friendly features, making it an ideal addition to any kitchen. This appliance is designed to enhance cooking performance while providing a sleek aesthetic that complements contemporary kitchen designs.

One of the standout features of the Hotpoint BFI62 is its multifunctional cooking options. With multiple cooking modes, including conventional, fan-assisted, and grill functions, users have the flexibility to prepare a wide range of meals to suit their preferences. The fan-assisted cooking mode ensures even heat distribution, allowing for perfectly cooked dishes, while the grill function is perfect for achieving that desired crispy finish on meats and vegetables.

Another notable characteristic of the BFI62 is its generous capacity. With a spacious interior, it allows users to cook larger meals or multiple dishes simultaneously, making it a great choice for families or those who love to entertain. Additionally, the oven is equipped with a telescopic rail system, providing easy access to dishes and reducing the risk of burns when checking on food.

The Hotpoint BFI62 also boasts a range of convenient technologies aimed at simplifying the cooking experience. The digital display and easy-to-use control panel make navigation intuitive, allowing users to set cooking times and temperatures with minimal effort. Furthermore, the oven features a built-in timer, ensuring that meals are cooked to perfection every time.

Cleaning the BFI62 is made hassle-free with its special catalytic lining, which helps break down food residue during the cooking process. This means less scrubbing for the user, as the oven essentially cleans itself, saving time and effort.

Safety is also a priority with the Hotpoint BFI62. The oven is designed with a cool door feature, ensuring that the outer surface remains safe to touch even during operation. This is particularly beneficial in homes with young children.

In summary, the Hotpoint BFI62 is a high-performance built-in oven that combines modern design with a multitude of features and technologies. Its multifunctional capabilities, spacious interior, user-friendly controls, and easy maintenance make it an excellent choice for both novice cooks and culinary enthusiasts alike.
Top Page Image Contents