Hotpoint CSX24X Use of Adapter Plug, U5-volt units, Refrigerator hcation, Clearances, Rollers

Installation Requirement (continued)–IMPORTANT,.. PleaSe Read Carefully.

	Use of Adapter Plug				a grounding type plug and outlet
	(U5-volt units)				and that the electrical rating of the
	Because of potential safety				cord be 15 amperes (minimum) and
					120 volts. Such extension cords are
	hazards under certain conditions,				obtainable through your local
	we strongly recommend against use				service organization.
	of an adapter plug. However, if you				The refrigerator should always
	still elect to use an adapter, where
					be plugged into its own
	local codes permit, aTEMPOWRY
					individual electrical outlet—
	CONNE~ION maybe made to a
					(115 volt, 60 Hertz, single phase
	properly grounded two-prong wall
					AC). This is recommended for
	outlet by use of a UL listed adapter
					best performance and to prevent
	(Fig. 2) available at most local
					overloading house wiring circuits,
	hardware	stores.
					which could cause a fire hazard
	TEMPORARY METHOD . .				from overheating ‘wires.
	(ADAPTER PLUGS NOT		nm’
	PERMITTED IN CANADAI				Refrigerator hcation
					Do not install refrigerator where
					temperature will go below 60°F.
		,			because it will not run often enough
I				I
					to maintain proper temperatures.
	The larger slot in the adapter must			. .
					Do install it on a floor strong
	be aligned with the larger slot in
					enough to support a fully loaded
	the wall outlet to provide proper
					refrigerator.
	polarity in the connection of the
					Also see Energy-Saving Tips
	power cord.
	CAUTION: Attiching adapter				regarding location.
ground terminal to wall outlet cover					Clearances
	screw does not ground the appliance
	unless cover screw is metal, and not				Allow the following clearances for
	insulated, and wall outlet is grounded				ease of installation, proper air
	through house wiring. You should
					circulation, and plumbing and
have the circuit checked by a qualified					electrical connections:
electrician to make sure the outlet					Sides. . . . . . . . . . . . . . . . . . . . 5/8”
	is properly grounded.
					Top . . . . . . . . . . . . . . . . . . . . . . . 1“
When disconnecting the power
					Back. . . . . . . . . . . . . . . . . . . . . . 1“
cord from the adapter, always hold
the adapter with one hand. If this					Allow the following door clearance:
	is not done, the adapter ground				Sides. . . . . . . . . . . . . . . . . . . . 3/4”

terminal is very likely to break with repeated use.

Water Supply to Icemaker

Should the adapter ground

Rollers

Adjustable rollers, which enable you to move your refrigerator away from the wall for cleaning, are located behind the base grille. These rollers should be set so that the refrigerator is firmly Positioned on the fl;or and the frofi~is raised just enough that the doors close easily when opened about halfway. Specially designed door hinges lift both doors slightly when opened. The force of gravity then helps close the door automatically.

I

pAT ‘/.~~~ce~

,,,N

##PULL OUT

,: #

To adjust rollers, remove the base grille by grasping it at the bottom and pulling it out.

Turn roller adjusting screws clockwise to raise refrigerator, counterclockwise to lower it. Use adjustable wrench (3/8” hex head bolt) or pliers.

When adjusting front rollers for proper door closure, it is recommended that the bottom front edge of the cabinet be approximately 5/8” from the floor.

terminal break; DONOT USE the appliance until a proper ground has again been established.

Use of Etiension Cords

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL listed 3-wire grounding type appliance extension cord having

You will need to connect your icemaker to a cold water line. A water supply kit containing copper

tubinz. shutoff valve, fittings and

e,

instructions is available at extra cost from your deder. There should be sufficient tubing for the icemaker from the cold water supply to allow you to move the refrigerator out from the wall several feet (approximately

3coils of l/4-inch copper tubing that measures at least 10 inches in diameter).

To replace base grille, align prongs on back of grille with clamps in cabinet and push forward until grille snaps into place.

4