Whirlpool UXT4230AD Installation Instructions, Electrical Requirements, Prepare Location

Page 7

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

INSTALLATION INSTRUCTIONS

Prepare Location

NOTE: It is recommended that the vent system be installed before hood is installed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

1.Disconnect power.

2.Depending on your model, determine which venting method to use: roof, wall or non-vented (recirculating).

3.Select a flat surface for assembling the range hood. Place covering over that surface.

4.Lift the range hood and set it upside down onto covered surface.

5.If cabinet has recessed bottom, add wood filler strips on each side. Install screws to attach filler strips in locations shown.

Wood filler strips (recessed cabinet bottoms only)

3" (7.6 cm)

Cabinet

bottom

Determine Wiring Hole Location

Cut only one 1¹⁄₄" (3.2 cm) diameter wiring access hole.

1.Determine and clearly mark a vertical centerline on the wall and cabinet in the area the vent opening will be made.

A

A. Centerline

3" (7.6 cm)

Wall

7

Image 7
Contents Hotte D’ASPIRATION DE Table of Contents Range Hood SafetyImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Makeup Air Installation ClearancesCold Weather Installations Venting Requirements¹⁄₄ x 10 8.3 cm x 25.4 cm Vent System Calculating Vent System LengthCm Round Vent System Example vent systemPrepare Location Installation InstructionsDetermine Wiring Hole Location Electrical RequirementsTo make a 3½ x 10½ 8.9 cm x 26.7 cm rectangle in the wall To wire through topTo wire through wall Wall VentingInstall Vent System Install Range HoodStyle 3 Cut Openings for 7 17.8 cm Round Vent Round vent knockout Rectangular vent knockout Power Supply Cable Installation Damper Flap Removal for 3¼ x 10 8.3 x 25.4 cm Vent ConnectorMake Electrical Connection Complete InstallationRange Hood Controls CleaningRange Hood USE Range Hood CareTo replace filter Wiring DiagramFor non-vented recirculating installations Replacing the Incandescent Light BulbCanada Assistance or ServiceAccessories U.S.AWhirlpool Major Appliance Limited Warranty Page Votre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreImportantes Instructions DE Sécurité Exigences demplacement Exigences DinstallationOutils et pièces Air d’appoint Installations dans les régions au climat froidExigences concernant l’évacuation Distances de dégagement à respecterExemple de circuit d’évacuation Méthodes d’évacuationCalcul de la longueur du circuit d’évacuation Système dévacuation avec conduits ronds de 7 17,8 cmComposant Longueur maximale recommandée = 35 pi 10,7 mSpécifications électriques Circuit dévacuation de 3¹⁄₄ x 10 8,3 cm x 25,4 cmCâblage à travers le sommet du placard Instructions D’INSTALLATIONPréparation de lemplacement Déterminer l’emplacement du trou de passage du câbleÉvacuation par le mur Installation du conduit d’évacuation Installation de la hottePlaque de protection pour mode recyclage Vis Raccordement électrique Installation du cordon dalimentationEntretien DE LA Hotte Achever l’installationCommandes de la hotte de cuisinière Utilisation DE LA HotteRemplacement de lampoule à incandescence Installations sans décharge à lextérieur recyclageRemplacement du filtre Marche Arrêt Arrêt Faible Élevé Schéma DE CâblageAccessoires Assistance OU ServiceAu Canada Garantie Limitée DES W10400322D

UXT4230AD, UXT4236AD specifications

The Whirlpool UXT4236AD and UXT4230AD are versatile and powerful range hoods designed to enhance your kitchen experience. Known for their solid build quality and effective functionality, these models offer both performance and aesthetic appeal, making them ideal choices for modern kitchens.

One of the main features of both the UXT4236AD and UXT4230AD is their reliable ventilation system. Equipped with a powerful three-speed fan, these range hoods efficiently eliminate smoke, odors, and grease from the air. Whether you are cooking a quick meal or preparing a feast, you can adjust the fan speed to suit your needs, ensuring that your kitchen remains comfortable and fresh during cooking sessions.

A notable technology integrated into these range hoods is the hassle-free ductless ventilation option. This feature allows homeowners with certain kitchen layouts the flexibility to convert the range hood for internal recirculation, eliminating the need for extensive ductwork. This is particularly advantageous for those living in apartments or homes without existing duct systems, as it simplifies installation while maintaining effective air purification.

Another characteristic that stands out in both models is their sleek and modern design. Available in a stainless steel finish, they enhance the kitchen's aesthetic while being easy to clean. The smooth surface helps prevent fingerprints and smudges, ensuring that the range hood maintains its luster over time.

In addition to functionality and design, both the UXT4236AD and UXT4230AD feature integrated LED lighting. This energy-efficient lighting illuminates the cooking surface, providing visibility for all your culinary adventures. It also adds an elegant touch and enhances the overall kitchen environment, making cooking a more enjoyable task.

The UXT4236AD boasts a slightly larger width of 36 inches, catering to expansive cooktops, while the UXT4230AD is perfectly sized at 30 inches, making it a suitable fit for smaller kitchens. Both models are designed with user-friendly controls, ensuring that adjustments can be made effortlessly, even with greasy hands.

With their blend of performance, versatility, and stylish design, the Whirlpool UXT4236AD and UXT4230AD are trusted choices for anyone looking to improve their kitchen's atmosphere and functionality, bringing together modern technology and practical solutions for everyday cooking needs.