Whirlpool 99044504A Install Range Hood, For vented installations, For non-vented installations

Page 9

Install Range Hood

1.Remove terminal box cover. Depending on your installation, remove either back or top wiring knockout.

A

A. Terminal box cover

2.Remove the rectangular and round vent connectors from hood. Set the connectors and screws aside for use if connecting to a rectangular vent system.

3.For vented installations:

■Check that the louver cover is installed in front of hood.

■Remove either top or rear rectangular vent knockout. If using round vent, remove both top rectangular and semicircular knockouts.

■If using rectangular vent, attach rectangular damper/vent connectors.

■Reinstall round vent connector.

NOTE: If the wall cap is directly behind the vent connector, the dampers in the connector and wall cap must not interfere with each other. Remove the vent connector damper if they interfere.

For non-vented installations:

■Remove louver cover from front of hood.

4.Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface.

A

A. Keyhole slot

5.Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes as shown.

A

A. Drill pilot hole

6.Install the 4 - #10 x ⁵⁄₈" mounting screws in pilot holes. Leave about ¹⁄₄" (6.4 cm) space between screw heads and cabinet to slide range hood into place.

¹⁄₄"

(6.4 mm)

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

7.For Direct Wire Installations:

■ Install a UL listed or CSA approved strain relief.

A

A. UL listed or CSA approved strain relief

■Pull about 12" (30 cm) of wire through wall or cabinet and into opening.

For Power Supply Installations:

■Follow instructions included with power supply cord kit marked for range hoods.

8.Using 2 people, lift range hood into final position, feeding electrical wire through wiring opening. Position the range hood so that the large end of the keyhole slots are over the screws. Then push the hood toward the wall so that the screws are in the neck of the slots. Tighten mounting screws to cabinet, making sure mounting screws are in narrow neck of slots.

9.Check that damper, if used, rotates up and down freely.

10.For Vented Installations Only:

Connect ventwork to hood. Seal joints with clamps to make secure and airtight.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Hotte D’ASPIRATION DE Table of Contents Range Hood SafetyFor vented installations, you also need Installation RequirementsTools and Parts Tools neededProduct Dimensions For Mobile Home InstallationsInstallation Clearances Location RequirementsVenting Requirements Vented Models Only Electrical Requirements Example vent system¹⁄₄ x 10 8.3 cm x 25.4 cm Vent System Determine Wiring Hole Location Installation InstructionsTo wire through rear wall To wire through topWall Venting Install Vent SystemFor vented installations Install Range HoodFor non-vented installations For Power Supply InstallationsComplete Installation Range Hood USEMake Electrical Connection Range Hood Care Assistance or ServiceThis limited warranty does not cover Whirlpool Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreConservez CES Instructions Exigences Dinstallation Exigences demplacementOutillage et pièces Exigences concernant lévacuation Installations pour régions à climat froidDégagements de séparation à respecter Air dappointCalcul de la longueur effective du circuit dévacuation Spécifications électriquesSystème de décharge de 7 17,8 cm Système de décharge de 3¹⁄₄ x 10 8,3 cm x 25,4 cmPréparation de lemplacement Instructions DinstallationDéterminer lemplacement du trou de passage du câble Câblage par le dessusDécharge à travers le mur Installation du conduit dévacuation Installation de la hotteInstallations avec décharge à lextérieur Installations sans décharge à lextérieurInstallations avec décharge à lextérieur seulement Pour les installations avec cordon dalimentation électriqueRaccordement électrique Raccordement par câblage directCommandes de la hotte de cuisinière Achever linstallationEntretien DE LA Hotte NettoyageInstallation sans décharge à lextérieur recyclage Assistance OU ServiceGarantie DES Gros Appareils Ménagers Whirlpool Corporation Si vous avez besoin de pièces de rechange99044504A/W10240546A

99044504A, W10240546A specifications

The Whirlpool W10240546A and W99044504A are essential components in modern kitchen appliances, particularly designed as replacement water filter cartridges for various Whirlpool refrigerators. These filters are integral for maintaining the health and safety of water dispensed from the fridge, ensuring that it meets high standards for quality and taste.

One of the standout features of the W10240546A and W99044504A filters is their advanced filtration technology. Utilizing a combination of carbon and other filtration materials, they are designed to reduce chlorine taste and odor, while also minimizing harmful contaminants such as lead, mercury, and pesticides. This results in cleaner, fresher-tasting water and ice. The filters are certified by the NSF, which ensures that they meet strict public health and safety standards.

Installation of these filters is straightforward, making it easy for users to replace them without the need for professional assistance. They are engineered to fit seamlessly into compatible Whirlpool refrigerator models, allowing for a hassle-free swap. Typically, these filters should be replaced every six months to ensure optimal performance and water quality, although the frequency may vary based on water usage and quality.

In addition to their impressive filtration capabilities, these water filters also embody energy-efficient design principles. By providing access to clean, refreshing water directly from the refrigerator, they help reduce reliance on bottled water, minimizing plastic waste and contributing to environmental sustainability.

Another characteristic of the W10240546A and W99044504A filters is their capacity to provide high flow rates. This means that users can enjoy ice and water on demand, without experiencing a significant drop in pressure or flow, even during peak usage times.

Moreover, Whirlpool showcases a commitment to innovation and quality in the materials used for these filters. The durable construction ensures longevity, making them a reliable choice for consumers looking to maintain the performance and longevity of their refrigerators. By investing in these filters, users can enjoy peace of mind, knowing that their family's water is not only convenient but also safe and healthy.

In summary, the Whirlpool W10240546A and W99044504A filters are exceptional products that combine ease of installation, high-performance filtration, and durability. They represent a practical solution for anyone looking to enhance the quality of their drinking water while being environmentally conscious. These filters are ideal for homeowners who prioritize health and taste in their daily lives.
Top Page Image Contents