Blender Safety
IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using electrical appliances, basic safety precautions should be followed, including the following:
• Read all instructions. | • To prevent damage to blender, jar, or cutter | |
• Plug into a grounded outlet. | assembly, DO NOT move or shake blender | |
• Do not touch surfaces that may be hot. | while in operation. If blending action stops during | |
operation, turn blender OFF, remove jar from | ||
Use handles or knobs provided. | ||
base, remove jar cover, and use a thin rubber | ||
• Extreme caution must be used when moving an | ||
spatula to push mixture towards cutters. | ||
appliance containing hot oil or other hot liquids. | ||
• Do not spray the base with a | ||
• Do not use appliance for other than intended use. | ||
spray gun. | ||
• To protect against electrical shock, do not | ||
• Disconnect power before cleaning or servicing. | ||
immerse cord, plug, or blender base in water | ||
• To prevent burns from hot liquids splashing out | ||
or any other liquid. | ||
of the jar, always remove the filler cap of the | ||
• Close supervision is necessary when any | ||
container cover before blending hot liquids. | ||
appliance is used by or near children. | ||
• Do not operate any appliance with a damaged | ||
• The use of accessory attachments not recom- | ||
cord or plug or after the appliance malfunctions, | ||
mended by Hamilton Beach may cause injuries. | ||
or is dropped or damaged in any manner. | ||
• To reduce risk of personal injury, unplug cord | ||
Return appliance to the nearest service facility | ||
from outlet when not in use, and before putting on | for examination, repair, or electrical or | |
or taking off parts or doing any other servicing of | mechanical adjustment. | |
the blender. | • If the supply cord of this appliance is damaged, | |
• Do not let cord hang over edge of table or | ||
it must be replaced by the manufacturer or its | ||
counter or touch hot surfaces. | service agent or a similar qualified person. If fitted | |
• Do not place on or near a hot gas or electric | with a | |
burner or in a heated oven. | approved by ASTA to be B.S. 1362 must be used. | |
• To reduce risk of personal injury and to prevent | If you need a replacement fuse carrier, it must be | |
damage to blender or jar and cutter assembly, | replaced by the same colour coded carrier with | |
DO NOT insert utensils into blender jar while | the same markings. Fuse covers and carriers | |
operating blender, or store utensils in the blender | can be obtained from approved service agents. | |
jar when it is not in use. | IMPORTANT: If the molded plug is cut off, | |
• Avoid contacting moving parts. | dispose of it immediately. The plug is not rewirable | |
and would cause a shock hazard if inserted into | ||
• Blades are sharp. Handle carefully. | ||
a socket. | ||
• Inspect jar and cutter assembly daily. Check | ||
• For a complete operation manual in this | ||
cutter for wear, nicks, or broken blades. Replace | ||
language, please visit our website at | ||
jar and cutter assembly at least every 12 months. | ||
www.commercial.hamiltonbeach.com | ||
• Do not defeat the jar pad sensors. | ||
or call |
•Do not use outdoors.
•This appliance is intended for short periods of operation, with a rated operating time of 3 minutes.
–SAVE THESE INSTRUCTIONS –
Blender Operation – Quick Start Guide
1.Place the blender on a dry, level surface.
2.Make sure the power switch is in the “off” or O position. Plug the blender into a grounded electrical outlet.
3.Place the jar on the base with ingredients and jar lid in place.
4.Set the controls to your preference.
5.Move the power switch to the “on” or I position (except model 915).
6.Move the power switch to start (run) or 
position.
3