Denon AVR-2803/983 manual SB D. Compch OUT 4 Jk, Dialogue Normalization

4	SURROUND	8tlBROUND	Display	the	"Dolby	Digital	EX		• DTS ES DSCRT6, 1
	pie_MEIER	P_AMEq_	surround	parameter				EQ.			EQ,
						CINEMA			CINEMA
									_:	_
	_	_	menu.			LFE 4		OdBb	LFE	_	OdBb
	(Main unit}	(Remote control	unit)			TONE		< [_	TONE		4
	NOTE: The display on the screen differs depending on					SBD. COMPCH OUT4 Jk			SBD. COMPCH OUTt
						<MTRX		ON	4MTRX		ON
	whether you are performing the operation from
								Yes4			Yes_
	the main unit or the remote control unit.
	Select the various	parameters.			_	Adjust	the	parameter	settings.
	(Main unit)	(Remote control unit)					(Main unit)		(Remote control unit)

•Dialogue Normalization

The dialogue normalization function is activated automatically when playing Dolby Digital program sources.

Dialogue normalization is a basic function of Dolby Digital which automatically normalizes the dialog level )standard level) of the signals which are recorded at different levels for different program sources, such as DVD, DTV and other future formats that will use Dolby Digital

These contents can be verified with the STATUS button.

Display

	..i	""	I	The number indicates	the normalization	level when the currently playing program is normalized	to the
I =,,,=i...........................i ,,JL,,, i	•"r:	H...=	I	standard level.

NOTE:

• When "Default" is selected and the _1 cursor button is pressed, "CINEMA EQ." and "D.COMR" are automatically turned off, "LFE" is reset, and the tone is set to the default value.

Surround parameters

CINEMA EQ. (Cinema Equalizer}:

The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for ovedy-bdght sounding motion picture

soundtracks Select this function if the sound from the front speakers is too bright.

This function only works in the Dolby Pro Logic II, Dolby Digital, DTS Surround, DTS NEQ:6 and WIDE SCREEN modes (The same contents are set for all operating modes)

D.COMR )Dynamic Range Compression):

Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds) For listening late at night, or

whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the soundtrack (but with reduced dynamic range) (This only works when playing program sources recorded in Dolby Digital or DTS) Select one of the four parameters ("OFF", "LOW', "MID" (middle) or "HI" (high)) Set to OFF for normal listening.

LFE (Low Frequency Effect}:

This sets the level of the LFE (Low Frequency Effect) sot_nds included in the source when playing program sot_rces recorded in Dolby Digital or DTS

If the sound produced from the subwoofer sounds distorted due to the LEE signals when playing Dolby Digital or DTS sources when the peak limiter is

turned

off with

the subwoofer

peak limit

level setting

(system setup menu), adjust

the

level as

necessary

Program source and adjustment range:

1.

Dolby

Digital:

-10

dB

to

O dB

2.

DTS

Surround:

-10

dB

to

0 dB

"_ When

DTS

encoded

movie

software

is played,

it

is recommended

that

the

LFE

LEVEL

be

set

to O dB for correct

DTS playback.

-_

When

DTS

encoded

music

software

is played,

it

is recommended

that

the

LFE

LEVEL

be

set

to -10 dB for correct

DTS playback.

TONE:

This adjusts the tone control (See "St_rrot_nd parameters _" on page 59)

SB CH OUT:

(1)Dolby Digital/DTS source

"OFF" ................... Playback is conducted without using the surround back speaker.

"NON	MTRX"	.Playback	is	conducted	using	the surround		back speaker.
		The same signals those of the surround channels are output from the surround back channels.
"MTRX ON". ......... Playback is conducted using the surround back speaker
		Surround back channel is reproduced					using digital		matrix	processing.
"NRML	(OFF)"	.Playback	is	conducted	without	using	the	surround	back	speaker.
"NRML	(ON)"	.Playback	is	conducted	using	the surround		back speaker.
		The same signals those of the surround channels are output from the surround back channels.

(2)Other source

"OFF" ................... Playback is conducted without using the surround back speaker. "ON" .................... Playback is conducted using the surround back speaker.

NOTE: This operation can be performed directly using the "SURROUND BACK" button on the main unit's panel

54