DeLonghi ETAM36.365 manual Menu Settings

MENU SETTINGS

To access the settings menu, press the button corresponding to MENU. Scroll through the menu by pressing the scrolling arrow (< or >) (fig. 9).

Rinsing

Use this function to deliver hot water from the spout to heat the internal circuit and make the coffee delivered hotter.

To enable the function, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Rinsing” is displayed;

3.Press the button. “Confirm?” is displayed;

4. Press the button (fig. 3). Hot water flows out of the spout, heating the internal circuit and making the cof- fee delivered hotter.

Descaling

For instructions on descaling, see page 18.

Install filter

For instructions on how to install the filter, see the section“Wa- ter softener filter” (page 19).

Replacing the filter (if installed)

For instructions on how to replace the filter, see the section “Replacing the filter” (page 20).

Adjust time

To adjust the time on the display, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until“Adjust time” is displayed;

3. Press the	button (fig. 3). The hours flash on the
display;

4.Press the scrolling arrow (< or >) (fig. 8) to change the hour;

5.Press the button to confirm. The minutes flash;

6.Press the scrolling arrow (< or >) (fig. 9) to change the minutes;

7.Press the button to confirm.

The time is set: press the MENU/ESC button to exit the menu.

Auto-start

You can set the auto-start time in order to have the appliance ready at a certain time (for example in the morning) so you can make coffee immediately.

Please note!

To enable this function, the time must already be set correctly.

To enable Auto-start, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until“Auto-start” is displayed;

3.Press the button. “Enable?” is displayed;

4.Press the button to confirm;

5.Press the scrolling arrow (< or >) to choose the hour;

6.Press the button to confirm;

7.Press the scrolling arrow (< or >) (fig. 9) to change the

	minutes;
8.	Press the	button to confirm;
9.	Press the MENU/ESC button to exit the menu.

Once the time has been confirmed, activation of auto-start

is indicated by the small bell (			) displayed alongside the
time.
To disable the function:
1.	Select auto-start from the menu;
2.	Press the	button. “Disable?” is displayed;
3.	Press the	button to confirm.
The small bell (		) is no longer displayed.

Auto-off

When this function is enabled:

- the appliance is automatically turned off completely, re- leasing the main switch. To turn the appliance on again, press the main switch (A20) and then the ON/stand-by button (A23).

When this function is disabled:

-the appliance switches to stand-by; power remains on and it consumes a minimal amount of electricity.

To turn the appliance on again, press the ON/stand-by button (A23).

The stand-by time can be modified using “Auto-off timer” (if “Auto-off” is enabled) or “Auto-standby timer ” (if “Auto-off” is disabled).

To enable or disable auto-off, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Auto- standby timer” (or Auto-off) is displayed;

3.Press the button. “Enable?” or “Disable?” is dis- played;

4.	Press the	button to confirm;
5.	Press the MENU/ESC button to exit the menu.

Auto-standby timer/ auto-off timer

Auto-off can be set so that the appliance goes off after 15 or 30 minutes, or 1, 2 or 3 hours.

To re-programme Auto-off, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Auto- standby timer” (or “Auto-off”) is displayed;

10