DeLonghi ESAM6600 manual Descale no, Descale YES, Appliance in Descale, Rinsing Fill Tank

Page 19

Press the OK button to activate auto-start.

Press the P button (corresponding to the ESC symbol flashing on the display) to exit programming mode

or

to change other parameters.

 

NOTE: When auto-start time is set, the symbol

appears alongside the time on the display.

17.3 Descaling

Over time, the continuous heating up of the water used to make the coffee leads to lime scale building up in the inner circuits of the appliance.

When the message:

DESCALE

flashes on the display, you should perform the descale cycle. Proceed as follows:

Make sure the appliance is ready.

• Press the P button then press the

button (corresponding to the

symbol flashing on the display)

then press the button repeatedly until the appliance displays:

 

 

 

DESCALE NO

 

• Press the

button (corresponding to the SET symbol flashing on the display) and the appliance dis-

plays:

 

 

 

DESCALE YES

Press the OK button to start the descale program.

Empty the water tank and pour in the contents of one bottle (4.2 fl. oz.) of DURGOL descaler plus 34 oz. of water. NOTE: Make sure splashes of descaler do not fall onto surfaces sensitive to acid such as marble, lime- stone and granite.

For subsequent descaling operations, use the same type and brand of descaling solution as supplied (avail- able from authorized technical service centers).

Attach the water spout to the nozzle.

Place a container with a minimum capacity of 34oz. under the hot water spout (Fig. 3).

Press the OK button. Descaler runs off from the hot water spout into the container below. The appliance displays:

APPLIANCE IN DESCALE

The descale program automatically performs a series of run offs and pauses to remove lime scale deposits from inside the coffee maker.

After about 30 minutes, the appliance displays:

RINSING FILL TANK

The appliance must now be rinsed through to eliminate residues of descaling solution from inside the appli- ance. Proceed as follows:

Empty the water tank, rinse and fill with clean water.

Reposition the tank.

Empty the full container and then put it back under the hot water spout.

Press the OK button. Hot water will run off from the spout into the container below and the appliance dis- plays:

RINSING

When the water tank is empty, the appliance displays the message:

RINSING COMPLETE PRESS OK

Press the OK button and refill the water tank with clean water.

The descale program is now terminated and the appliance is ready to make coffee again.

 

18

 

 

C o l l e c t i o n

 

 

 

Image 19
Contents De’Longhi America, Inc Collection Colleción Collezione L l e c t i o n L l e c i ó n L l e z i o n e L l e c t i o n L l e c i ó n L l e z i o n e Changing the Quantity of Coffee and Milk for IndexP O R T a N T S a F E G U a R D S Description see Safety WarningsControl panel Press OK Press OK to Install EnglishEnglish Installed Fill TankTurning on and Preheating Preparing Coffee Using Coffee Beans and Useful TipsHeating UP Please Wait Rinsing Please WaitEmpty Grounds Container Ground TOO Fine Adjust Mill Insert Water Spout and Press OKChanging the Quantity of Coffee in the CUP Ready PRE-GROUND CoffeeRegulating the Coffee Mill HOT Water Program Quantity HOT WaterCappuccino Container Pointer in Position Preparing Frothed or Steamed Milk Without Coffee CleaningItalian Macchiato Container Pointer in Position Preparing Latte or Italian MacchiatoMilkfor Programquantity Cleaning and MaintenanceCleaning the coffee maker Cleaning the infuserCorrect Incorrect Start Time Changing and Setting the Menu ParametersAUTO-START no Appliance in Descale DescaleDescale no Descale YESWater Hardness High TemperatureReset to Default no OFF After 1 HourBeep ON/OFF activates and deactivates the beep Changing the LanguageLess Coffee TroubleshootingProblem Cause Solution Problems to be Resolved Before Calling the Service CenterBut From Around How long does the coverage last? What does the warranty cover?What is not covered by the warranty? How do you get service?