Customising the espresso “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml of espresso “MY COFFEE”.
To modify these settings, proceed as follows:
1.Place a cup under the coffee spouts ( fig. 10).
2.Press the 
button repeatedly (fig. 8) until “MY COFFEE” is displayed.
3.Keep the 
button (fig. 2) pressed until the message “Program quantity” is displayed. Release the button. The machine starts making the coffee;
4.As soon as the coffee in the cup reaches the required level,
press the 
button again.
The quantity set has now been programmed.
Programming the long “my coffee” quantity
The appliance is set by default to automatically deliver about 100ml of LONG “MY COFFEE”. To modify this quantity, proceed as follows:
1.Place a cup under the coffee spouts ( fig. 16).
2.Press the 
button repeatedly (fig. 8) until “MY COFFEE” is displayed.
3.Keep the LONG button (fig. 9) pressed until the message “Program quantity” is displayed. Release the button. The machine starts making the coffee;
4.As soon as the coffee in the cup reaches the required level, press the LONG button again.
The quantity set has now been programmed.
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and should not require regulating initially.
However, if after making the first few coffees you find that delivery is either too fast or too slow (a drop at a time), this can be corrected by adjusting the grinding adjustment knob (fig. 11).
Please note!
The grinding adjustment knob must only be turned when the coffee mill is in operation.
For faster delivery (not a drop at a time), turn one click clockwise towards “7” (coarser ground coffee).
For fuller bodied creamier coffee,
turn one click anticlockwise towards “1” (finer ground coffee).
These adjustments will only be evident after at least 2 cups of coffee have been delivered.
If delivery is still too fast or too slow, repeat the correction, turning the knob another click.
Tips for a hotter coffee
For a hotter coffee, you are recommended to:
•before delivering the coffee, perform a rinsing cycle by
pressing the 
button to select the “Rinsing” function. Hot water is delivered from the spout, heating the internal circuits of the appliance and thus raising the coffee temperature.
•If “Cup warmer” mode has been enabled, place the cups on the cup warmer until they are warm.
•warm the cups by rinsing them with hot water
•set the “high” coffee temperature (••••) in the menu.
Making espresso coffee using coffee beans
Important!
Do not use caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable.
1.Fill the container with coffee beans (fig. 12).
2.Place under the coffee spouts:
-1 cup, if you want to make 1 coffee (fig. 10);
-2 cups, if you want 2 coffees (fig. 13);
3.Lower the spouts as near as possible to the cup. This makes a creamier coffee (fig. 14).
4.Press the button corresponding to the number of coffees
required (1 cup 
or 2 cups 
) (fig. 2 and 15).
5.Preparation begins. The quantity and taste of coffee selected is displayed together with a progress bar which
gradually fills as preparation progresses.
Once the coffee has been made, the appliance
Please note:
•While the machine is making coffee, delivery can be interrupted at any moment by pressing one of the coffee
buttons (
or
).
•At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) one of the coffee
buttons (
or
).
Once the coffee has been made, the appliance is ready to use again.
Important!
If the coffee is delivered a drop at a time, too fast and not creamy enough or too cold, read the tips in the “Troubleshooting” section on page 19.
Various alarm messages could be displayed while using the machine. Their meaning is explained in the section “Displayed messages” (page 18).
12