Black & Decker DE710 manual Guarde Estas Instrucciones, Carafe Care, Mineral Deposits and Clogging

Page 4

2. To clean inside, open the one-piece water reservoir and brew basket lid. Wipe surfaces with a damp cloth, close the one-piece water reservoir and brew basket lid (A).

A

Carafe Care

A damaged carafe may result in possible burns from a hot liquid. To avoid breaking:

Do not allow all liquid to evaporate from the carafe while on the "Keep Hot" plate or heat the carafe when empty.

Discard the carafe if chipped, cracked, or damaged in any manner.

Never use abrasive scouring pads or cleansers; they will scratch and weaken the glass.

Do not place the carafe on or near a gas or electric burner, in a heated oven, or in a microwave oven.

Avoid rough handling and sharp blows.

Mineral Deposits and Clogging

Mineral deposits left by hard water can clog your coffeemaker. Cleaning is recommended every 3 months. Excessive steaming or a prolonged brewing cycle is a sign that a cleaning is needed. The frequency of flushing out deposits is affected by your usage and water hardness. During cleaning, more steaming occurs than when brewing coffee and may emit spurts of steam.

1.Pour white vinegar into water reservoir up to 6-cup level on water viewer. Add water up to 12-cup line.

2.Put a paper filter in the brew basket and close the cover. Set empty carafe on the "Keep Hot" plate.

3.Turn on coffeemaker and let half the cleaning solution brew into carafe (till water level goes down to around "5"). Turn off coffeemaker and let it soak for at least 15 minutes to soften the deposits.

4.Turn on coffeemaker and brew remaining cleaning solution into carafe.

5.Turn off coffeemaker, empty carafe and discard soiled filter.

6.Fill reservoir with water to 12-cup line, replace empty carafe, then turn on coffeemaker for a complete brew cycle to flush out remaining cleaning solution. You may have to repeat this to eliminate the vinegar smell/taste.

7.Wash the brew basket and carafe as instructed in "CLEANING".

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Cuando se utilizan aparatos eléctricos, siempre se debe respetar ciertas medidas de seguridad a fin de reducir el riesgo de un incendio, un choque eléctrico y (o) lesiones a las personas, incluyendo las siguientes:

Por favor lea todas las instrucciones.

No toque las superficies calientes. Utilice las asas o las perillas.

A fin de protegerse contra el riesgo de un choque eléctrico, no coloque el aparato de manera que el cable, el enchufe o el mismo aparato entre en contacto con agua o cualquier otro líquido.

Todo aparato eléctrico utilizado en la presencia de menores de edad o por ellos mismos requiere la supervisión de un adulto.

Desconecte el aparato de la toma de corriente cuando no esté en funcionamiento y antes de limpiarlo. Espere que el aparato se enfríe antes de instalar o retirar las piezas y antes de limpiarlo.

No se debe utilizar ningún aparato eléctrico que tenga el cable o el enchufe averiado, que presente un problema de funcionamiento o que esté dañado. Devuelva el aparato al centro de servicio autorizado más cercano para que lo examinen, reparen o ajusten. Si el producto llegase a fallar dentro del período de la garantía, llame gratis al número apropiado que aparece en la cubierta de este manual para obtener información relacionada al servicio de mantenimiento del aparato.

El uso de un accesorio no evaluado para ser utilizado con este aparato podría ocasionar lesiones personales.

Este aparato no se debe utilizar a la intemperie.

No permita que el cable cuelgue del borde de la mesa o del mostrador ni que entre en contacto con las superficies calientes.

No coloque el aparato sobre ni cerca de las hornillas de gas o eléctricas ni adentro de un horno caliente.

La jarra debe permanecer tapada cuando está en uso.

La jarra está diseñada para ser utilizada con este aparato. Jamás se deberá utilizar sobre la estufa.

Nunca coloque una jarra caliente sobre una superficie fría ni húmeda.

No utilice la jarra si el vidrio se encuentra rajado o si el asa está débil.

No limpie la jarra con limpiadores abrasivos, con almohadillas de fibra de metal ni demás limpiadores abrasivos.

El aparato se deberá utilizar únicamente con el fin previsto.

Existe el riesgo de quemaduras si uno retira la tapa durante los ciclos de colado.

GUARDE ESTAS INSTRUCCIONES.

5

6

Image 4
Contents Please Read and Save this Use and Care Book Model Modelo Modèle DE710USA/Canada Mexico01-800-714-2503 Polarized Plug 120V Models Only Important SafeguardsTAMPER-RESISTANT Screw Electrical Cord How to Use Care and CleaningCleaning Getting StartedCarafe Care Guarde Estas InstruccionesMineral Deposits and Clogging Enchufe Polarizado Cable ÉlectricoComo usar Cuidado y limpiezaImportantes Mises EN Garde Conserver CES MesuresFiche Polarisée Modèles de 120 V seulement VIS IndesserrableEntretien et nettoyage UtilisationPréparatifs Entretien de la carafe Dépôts de minéraux et blocageNeed HELP? ¿NECESITA AYUDA?Besoin D’AIDE? Avertissement Afin 900 W 120 V 60 Hz

DE710 specifications

The Black & Decker DE710 is a versatile and reliable power tool that caters to a wide range of construction and DIY needs. Designed with both professionals and hobbyists in mind, the DE710 combines quality engineering with user-friendly features, making it an indispensable addition to any toolkit.

One of the key features of the DE710 is its powerful motor. With a robust 7.0 Amp motor, this drill provides ample power for drilling through various materials, including wood, metal, and plastic. The motor's design ensures that it delivers consistent performance, allowing users to tackle a variety of tasks with ease.

Another notable characteristic of the Black & Decker DE710 is its variable speed control. Users can easily adjust the speed from 0 to 800 RPM, which adds a level of precision to the drilling process. This feature is particularly useful when working with different materials or when a more delicate touch is required. The option to switch between high and low speed settings enhances the tool’s versatility and adaptability.

The DE710 also boasts a keyless chuck that allows for quick and hassle-free bit changes. This user-friendly design feature eliminates the need for additional tools, enabling users to switch between drill bits swiftly and efficiently. This is especially beneficial during multitasking or when time is of the essence.

Ergonomics plays a significant role in the DE710's design. It features a lightweight build that ensures ease of handling, while the soft-grip handle provides comfort during prolonged use. The lightweight nature of the tool minimizes user fatigue, making it ideal for extended projects.

The Black & Decker DE710 also incorporates built-in safety features, including a locking trigger and a sturdy casing. These enhancements not only improve user safety but also ensure the tool's longevity and durability in demanding work environments.

In summary, the Black & Decker DE710 is a powerful, user-friendly drill that combines variable speed control, a keyless chuck, and ergonomic design to support a wide variety of tasks. Its features cater to both efficiency and comfort, making it a favorite among DIY enthusiasts and professionals alike. Whether you're drilling holes for shelves or assembling furniture, the DE710 is designed to meet your needs with reliability and ease.