Black & Decker FP2500SC, FP2500C Off/Pulse, HOW to Chop in the Workbowl, Using the Dough Blade

Important: For your protection this appliance has an interlock system. The processor will not operate unless the workbowl, cover and wide-mouth feed chute are properly locked in place.

3.Place the wide-mouth feed chute on top of the cover with the small tab to the right of the workbowl’s handle. Turn clockwise until it clicks into position over the handle.

4.Insert the food pusher into the central tube of the wide-mouth feed chute. Turn clockwise to lock in place. The pusher is used to guide foods through the feed chute and can be removed when adding liquid or additional foods while the processor is running. To remove, turn counterclockwise.

Important: Never use your fingers to direct food through the chute.

6. Select your desired speed (PULSE (P), LOW or HIGH).

Note: Process foods for no more than a few seconds at a time. Pulsing produces excellent results and offers greater control.

7.If using small workbowl, press OFF/PULSE (O/P) and wait for blades to stop revolving. If using large workbowl, food can be added while processor is running; remove food pusher and insert food through the feed chute. Replace food pusher in chute.

Important: Be sure chopping blade has completely stopped spinning before removing cover from processor.

CONTROLS

F

The controls are located on the front of the base (F). Press PULSE (P), HIGH or LOW to select a function (see directions below).

OFF/PULSE:

•Processor should be stored in OFF (0) position and unplugged when not in use.

8.Press the OFF/PULSE (O/P) button and allow blades to stop revolving before removing cover. Twist cover toward to remove.

9.Unlock workbowl by turning it counterclockwise and lift off base.

Note: Remove bowl from appliance before removing blade to prevent food from leaking through the center opening of the bowl.

10.Carefully remove chopping blade.

11.Unplug appliance when not in use.

•Use PULSE (P) for short processing tasks. This lets you control the size and uniformity of foods being chopped.

•The OFF/PULSE (O/P) button must be pressed and held for the appliance to operate in PULSE (P) mode. When released, the appliance will stop.

•The motor of the processor will run as long as the OFF/PULSE (O/P) button is held down. Press the button and then release to allow the blades to stop running and the food to fall to the bottom of the workbowl.

•Pulsing gives better control when chopping, mincing, mixing and blending foods. You can control the size of the foods, from coarse to fine.

HIGH and LOW:

When either speed is selected, the processor will run continuously until the OFF/ PULSE (O/P) button is pressed.

HOW TO CHOP IN THE WORKBOWL:

The chopping blade is used to coarsely or finely chop, mince, mix and puree foods to a smooth consistency.

1.Lock workbowl into position (see Illustrations B and C).

2.Hold chopping blade by center shaft and insert onto center

	post (G).
G	Caution: The blade attachments are very sharp. Use caution
	when handling and storing.

3.Place food in workbowl.

4.Place cover on workbowl and lock into place by rotating clockwise (see Illustration D).

5.When using large workbowl, place the wide-mouth feed chute and food pusher in place.

5

Helpful Tips for Chopping and Blending:

•The processor works very quickly.

•Watch carefully to avoid over-processing foods.

•The PULSE (P) button offers the best control and results.

•For best results, process foods that are about the same size.

•Do not overload the bowl.

•Never walk away from the processor while it is on.

•Use hot but never boiling liquids.

•Do not process more than ¾ cup liquid in the small workbowl and 3 cups liquid in the large workbowl at one time.

•To process meat, use no more than ¾ cup in the small workbowl and 2 cups of ¾-inch cubes. Process using PULSE (P) in 5 second intervals.

•The small workbowl has a capacity of 3 cups and the large workbowl has a capacity of 10 cups.

•Insert a funnel into the feed chute when adding ingredients such as, oil, flour and sugar.

USING THE DOUGH BLADE

This blade makes preparing dough and pastry efficient and time-saving.

1.This blade does not extend to the outside rim of the workbowl, so it cannot incorporate flour when very small amounts of flour are being processed.

Note: Use the metal blade for mixtures that contain less 2 cups of flour. 2. Push dough blade down as far as it will go into workbowl.

6