Kenwood KMM020, KMC010 manual Troubleshooting, To fit and use your splashguard, Problem

Page 6

troubleshooting

solution

solution

problem

●The whisk or K-beater knocks against the bottom of the bowl or isn’t reaching the ingredients in the bottom of the bowl.

●Adjust the height using the spanner provided. Here’s how:

1Unplug the appliance.

2Raise the mixer head and insert the whisk or beater.

3Lower the mixer head. If the clearance needs to be adjusted, raise the mixer head and remove the tool. Ideally the whisk and K-beater should be

 

almost touching the bottom of the bowl .

 

4

Using the spanner provided loosen the nut

sufficiently to allow

 

adjustment of the shaft . To lower the tool closer to the bottom of the

 

bowl, turn the shaft anti-clockwise. To raise the tool away from the bottom

 

of the bowl turn the shaft clockwise.

 

5

Re-tighten the nut.

 

6Fit the tool to the mixer and lower the mixer head. (Check its position see points above).

7Repeat the above steps as necessary until the tool is set correctly. Once this is acheived tighten the nut securely.

dough hook - this tool is set at the factory and should require no adjustment.

problem

●The mixer stops during operation.

●Your mixer is fitted with an overload protection device and will stop if overloaded to protect the machine. If this happens, switch off and unplug the mixer. Remove some of the ingredients to reduce the load, and allow the mixer to stand for a few minutes. Plug in and reselect the speed. If the mixer does not restart immediately allow to stand for additional time.

to fit and use your splashguard

1Raise the mixer head until it locks.

2 Fit the bowl onto the base.

3

Push the splashguard onto the underside of the mixer head

until fully

 

located. The hinged section should be positioned as shown.

 

4

Insert required tool.

 

5Lower the mixer head.

●During mixing, ingredients can be added directly to the bowl via the

hinged section of the splashguard

.

●You do not need to remove the splashguard to change tools.

6Remove the splashguard by raising the mixer head and sliding it down.

7

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Chef and Major KMC010 KMM020 series ´dw Before using your Kenwood appliance Before using for the first timeBefore plugging Know your Kenwood kitchen machine Know your Kenwood kitchen machineTo use your mixer Speed switchMixing tools and some of their uses Points for bread makingTroubleshooting ProblemTo fit and use your splashguard Roto food cutter Flat pasta makerPasta maker Fruit pressPage Service and customer care Cleaning and serviceCare and cleaning Guarantee UK onlyRecipes PavlovaScrumptious chocolate cake Chocolate mousseline fillingChilli marinade ±∑UFW ËÅHU‹ «∞∑COd Au… ±u «∞AuØuô¢W«∞LFπMU‹ -«‹ «∞IAd… «∞NAW ËÅHU‹ «∞∑COd±d≤m «∞∂U≠Ku≠U «∞bÆOo œ≠FW Ë«b…«∞BOU≤W ˸´U¥W «∞FLö¡ «∞∑MEOn Ë«∞ªb±W´ö±W ßKW ±NLö‹ -«‹ «∞Fπö‹ ±ADuW «∞FMU¥W Ë«∞∑MEOn«∞J∂Od… ËÅU≤FW «∞J∂W «∞AU±OW ¸±e «∞LKIWPage «∂Dw «∞ºKDU≤OW ´Kv «∞IU´b… «¸≠Fw ¸√ «∞FπU≤W ∑v ¢IHq ¢dØOV Ë«ß∑ªb«Â ±U≤l «∞d-««ß∑JAU· «îDU¡ Ë≈ÅöNU «∞ªö ≠u¸«Î ≠U¢dØOt ∞H∑d… ≈U≠OW ∑v ¥∂dœ≤IU ≥U±W ∞∑COd «∞ª∂e ±H∑UÕ «∞ºd´W OU÷ «∞∂Oi«∞JLOU‹ «∞IBuÈ Ôß∑FLU‰ «∞ªö«ß∑JAU· §NU «∞LD∂a «∞L∑JU±q ±s Doownek «±UÊ ∂q «ôß∑FLU‰ ∞KLd… «ôË∞v∂q «∞∑uÅOq U∞JNdU¡ ∂q «ß∑ªb«Â §NU Doownek
Top Page Image Contents