Xantech PA1235X installation instructions Installation Physical Location and Mounting

Page 7

Model PA1235X

Page 7

INSTALLATION - PHYSICAL LOCATION AND MOUNTING

Upper shelf, component, wall, etc.

PA1235X

Keep perforations on top cover free of

obstructions for max. cooling effect.

2-inch spacing (minimum)

To maximize air flow, route

Convection

Keep perforations on bottom

single large opening in lower shelf.

Airflow

plate free of obstructions.

Figure 4 – PA1235X Horizontal Mounting

When you mount the PA1235X, you should plan its location carefully. Pay close attention to each of the following factors:

1.The amplifier is convection cooled. That is, it depends on the natural free flow of air up through the slot perforations in the bottom plate, over the internal heat dissipating fins, then out the top cover, for adequate cooling.

2.If mounted in an equipment cabinet or other confining location, allow at least 2 inches of space above the top cover (see Fig. 4). Be sure there are large openings in the shelf below the unit and in the cabinet to allow the entry of cool air and the escape of warm air.

Note: Do not remove feet in shelf-top installations.

3.If the cabinet contains other heat generating components or you are using several PA1235X's in a large multi-zone system, you will have to pay even closer attention to adequate ventilation.

4.Do not hesitate to use fans (quiet, boxer type), if necessary, to ensure a constant flow of air through the PA1235X's and the other heat generating components.

5.When mounting in a 19" (483mm) rack, adding a single RU (Rack Unit) above and below the PA1235X will improve convection in heavy use applications.

[One Rack Unit size = 1-3/4" (44.5mm) in height].

6.In multi-zone installations, you will have large bundles of wire and cable to accommodate audio, video and speaker connections. Be sure to allow enough room for the leads and dress them in such a manner so as not to block airflow.

7.The PA1235X is designed for mounting into standard 19" Rack Panels or on flat horizontal surfaces. When mounting into a 19" rack, use the rack panel cup washers and screws supplied.

NOTE: You should consider some sort of rear support for rack mounted units when used in mobile applications or when located in seismically active areas.

© 2002 Xantech Corporation.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Table of Contents Model PA1235X Channel Power AmplifierNot Expose this Appliance to Rain or Moisture Safety Instructions Read Before Operating EquipmentGeneral Information Rack Panel Handles PA1235X Panel and Feature DescriptionsModel PA1235X Model PA1235X PA1235X Installation Physical Location and MountingStereo Mode Connections Connecting the PA1235XSpeaker Phasing Connecting the Remote ON/OFF JackPreamplifier, Control Center, etc RF Signal IR Signal Multi-Zone System Diagram Using The PA1235XProblem Probable Cause and Solution Trouble ShootingSpecifications Model PA1235X Model PA1235X Xantech Corporation Xantech Corporation
Related manuals
Manual 1 pages 54.75 Kb

PA1235X specifications

The Xantech PA1235X is a powerful, professional-grade amplifier that caters to the needs of both commercial and residential sound applications. With a robust design and advanced features, it is well-suited for use in various environments, including retail spaces, restaurants, and home theater systems.

One of the standout features of the PA1235X is its high power output. It delivers 35 watts per channel at 8 ohms, allowing it to drive speakers effectively in larger rooms while ensuring clear and dynamic sound reproduction. The amplifier also offers a total output of 70 watts when bridged, providing users with the versatility to adjust their setup according to the spatial requirements of the listening area.

The PA1235X employs Class D amplification technology, which is known for its energy efficiency and lightweight design. This feature not only reduces electricity consumption but also minimizes heat generation, making the amplifier suitable for prolonged use without the risk of overheating.

In addition to its power and efficiency, the PA1235X boasts a range of input options, including balanced and unbalanced connections. This flexibility allows users to connect a variety of audio sources, whether it be a microphone, mixer, or existing audio systems. The amplifier is equipped with RCA and XLR inputs, ensuring compatibility with professional and consumer-grade audio equipment alike.

Another notable characteristic of the Xantech PA1235X is its built-in protection circuitry. This safeguards the device against overheating, short circuits, and overloading, thereby extending its lifespan and maintaining reliable performance.

For added convenience, the amplifier features a front-panel volume control, allowing users to easily manage audio levels without needing to access a remote or external control unit.

The Xantech PA1235X is not only designed with performance in mind but also emphasizes user-friendliness. Its compact form factor and rack-mountable design make it ideal for integration into AV setups without taking up excessive space.

Overall, the Xantech PA1235X stands out for its combination of power, flexibility, and reliability. Whether for use in a professional setting or a personal audio setup, it delivers excellent sound quality and adaptability to meet diverse audio demands.
Top Page Image Contents