Jenn-Air LIB0057678 Install In-line Blower System Outlet Side, Inlet Side, Complete Preparation

Page 11

Install In-line Blower System

NOTE: The blower motor housing can be mounted using 4 holes from either the inlet side or the outlet side of the blower.

Outlet Side

AA

A

A

A. Mounting holes

Inlet Side

A

A

A. Mounting holes

1.Position the in-line blower motor housing in its mounting location and mark the 4 mounting hole locations.

2.Drill 4 mounting pilot holes using a ³⁄₁₆" (4.8 mm) drill bit.

3.Attach the in-line blower motor housing to the mounting location with 4 - 6 x 80 mm mounting screws and washers.

4.If it is removed, reinstall the blower motor assembly and secure it with the screws previously removed.

5.If it is removed, reattach the motor electrical plug to the connector on the blower motor assembly.

Complete Preparation

1.Determine and make all necessary cuts for the vent system.

IMPORTANT: When cutting or drilling into the floor, ceiling or wall, do not damage electrical wiring or other hidden utilities.

2.Determine the location where the ¹⁄₂" (1.3 cm) wiring conduit will be routed through the floor, ceiling or wall between the in- line blower and the downdraft vent.

3.Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4.Locate the electrical terminal boxes in the in-line blower housing and downdraft vent. Remove the terminal box covers and set the covers and screws aside.

B

A

A. Electrical terminal box

B. Electrical knockout

5.Remove the electrical knockout from the in-line blower housing and downdraft vent to prepare for the installation of the UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit and conduit connector.

6.With the downdraft vent mounted, run the ¹⁄₂" (1.3 cm) wiring conduit between the in-line blower motor housing and the downdraft vent. Pull enough ¹⁄₂" (1.3 cm) wiring conduit to allow for easy connection to the terminal boxes in the in-line blower housing and downdraft vent.

7.Run the six 18 AWG wires through the ¹⁄₂" (1.3 cm) wiring conduit and conduit connectors and into the terminal boxes on the in-line blower housing and downdraft vent. Leave enough wire length in each terminal box to make the wiring connections.

8.Install the conduit connectors and conduit to the in-line blower housing and downdraft vent electrical terminal boxes.

9.Connect the vent system to the downdraft vent and in-line blower system and seal all joints with clamps.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents LIB0057678/W10526413C JENN-AIR36 91.4 CM Accolade Downdraft Ventilation SystemTable of Contents Your safety and the safety of others are very important Vent System SafetyImportant Safety Instructions Location Requirements Installation RequirementsTools and Parts Countertop Cutout Dimensions Product Dimensions Cabinet DimensionsRecommended Vent System Length Cold Weather InstallationsElectrical Requirements Venting RequirementsCalculating Vent System Length Installation InstructionsVenting Methods Downdraft Vent System PreparationVent Collar and Vent Transition Installation Install Downdraft Vent SystemPrepare the In-line Blower System Install Downdraft Vent In-Line External Type Blower MotorPrepare for Mounting the In-Line Blower System Complete Preparation Install In-line Blower System Outlet SideInlet Side Electrical Connection Inside In-line Blower System Make Electrical Connections for In-Line Blower Motor SystemGrounding Instructions Complete InstallationDowndraft Mounted Controls Remote Up/Down SwitchDowndraft Vent System USE Operating Downdraft Vent SystemRemote Control Operation Filters Vent System CareSurface of Downdraft Vent GlassReplacing the Fuse User Servicing InstructionsSEL0053854 DiagramwiringU.S.A Assistance or ServiceJENN-AIRMAJOR Appliance Warranty AccessoriesCall This limited warranty does not coverVotre sécurité et celle des autres est très importante Sécurité DU Système DE VentilationImportantes Instructions DE Sécurité Outillage et pièces Exigences DinstallationExigences d’emplacement Plan de travail Dimensions des ouvertures à découper Dimensions du produit Dimensions du placardExigences concernant l’évacuation Longueur recommandée du circuit d’évacuationInstallations dans les régions au climat froid Spécifications électriquesCalcul de la longueur du circuit d’évacuation Instructions D’INSTALLATIONMéthodes d’évacuation Préparation du système dextraction Par le basInstallation du système dextraction Par le bas Préparation du système de ventilation en ligne Préparation du montage du système de ventilation en ligneAchever la préparation Installation du système de ventilation en ligneCôté sortie Côté entréeSerrer les vis du bornier Déconnecter la source de courant électriqueInstructions de liaison à la terre Achever l’installationCommutateur de montée/descente déporté Commandes montées sur lextracteurFonctionnement du système dextraction Par le bas Utilisation du système dextraction par le basFonctionnement de la télécommande Vitre Remplacement des piles de la TélécommandeEntretien DU Système Dextraction Surface du système dextraction par le basInstructions DE Dépannage Pour Lutilisateur Remplacement du fusibleGris CdsâblageechémaSi vous avez besoin de pièces de rechange Assistance OU ServiceAccessoires Au CanadaLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers JENN-AIRPage W10526413C

LIB0057678, W10526413C specifications

The Jenn-Air W10526413C, LIB0057678 is a high-performance kitchen appliance designed to elevate culinary experiences and enhance kitchen aesthetics. This premium model is part of the renowned Jenn-Air brand, celebrated for its commitment to innovation, quality, and luxury in home appliances.

One of the standout features of the Jenn-Air W10526413C is its sophisticated design, seamlessly integrating into modern kitchens. With a sleek, stainless steel finish and elegant lines, it complements a variety of decors and adds a touch of sophistication to any cooking space. The appliance’s user-friendly interface includes intuitive controls, making it easy for home chefs to access a multitude of settings and features.

Key technologies incorporated in the Jenn-Air W10526413C include Smart Temperature Management, which ensures precise control over cooking temperatures, enabling users to achieve optimal results for a range of dishes. This technology also helps maintain consistent temperature levels, reducing cooking time and improving energy efficiency. Additionally, the appliance features advanced cooking modes such as convection baking, broiling, and roasting, allowing for versatility in meal preparation.

One of the highlights of this model is its powerful ventilation system, which efficiently eliminates smoke, steam, and odors from the kitchen. The integrated hood provides effective airflow, ensuring a clean and comfortable cooking environment. This is complemented by the appliance's quiet operation, which minimizes disruptions during meal prep and family gatherings.

The Jenn-Air W10526413C is designed with practicality in mind; it includes ample cooking space and adjustable racks that can accommodate various dish sizes and cooking methods. The appliance's durable construction guarantees longevity, making it a worthwhile investment for any home cook or culinary enthusiast.

Moreover, the Jenn-Air W10526413C supports Wi-Fi connectivity, enabling users to control and monitor the appliance remotely through their smartphones or smart home systems. This feature not only enhances convenience but also allows for seamless integration into modern smart kitchens.

Overall, the Jenn-Air W10526413C, LIB0057678 is a remarkable addition to any kitchen, combining cutting-edge technology, elegant design, and versatility. Whether you are preparing a simple weeknight dinner or hosting an elaborate gathering, this appliance is engineered to meet the demands of any culinary endeavor while adding a touch of luxury to your cooking experience.
Top Page Image Contents