Jenn-Air LIB0057678 Electrical Requirements, Venting Requirements, Recommended Vent System Length

Page 7

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located on the front of the downdraft vent.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

Venting Requirements

IMPORTANT: Make sure there is proper clearance within the wall or floor before making exhaust vent cutouts.

■Use heavy (rigid) metal vent.

■Venting system must terminate to the outside.

■Do not terminate the vent system in an attic or other enclosed area.

■Do not use 4" (10.2 cm) laundry-type wall caps.

■Do not install 2 elbows together.

■Do not use plastic or metal foil vent.

■The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.

■Use no more than three 90° elbows

■Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than one elbow is used.

■Use clamps or duct tape to seal all joints in the vent system.

■Use caulking tape to seal the exterior wall or floor opening around cap.

■Do not cut joist or stud. If vent cutout falls over a joist or stud, a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate each foot of flexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended Vent System Length:

The vent system length should not exceed the maximum lengths listed in the Maximum Length of Vent System chart. See “Calculating Vent System Length” in the “Venting Methods” section in the Installation Instructions for the interior- or exterior- mounted vent motor.

Cold Weather Installations

An additional back draft damper should be installed to minimize backward cold air flow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your area.

See the “Accessories” section for information on ordering optional kits.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents LIB0057678/W10526413C JENN-AIR36 91.4 CM Accolade Downdraft Ventilation SystemTable of Contents Your safety and the safety of others are very important Vent System SafetyImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Countertop Cutout Dimensions Product Dimensions Cabinet DimensionsRecommended Vent System Length Cold Weather InstallationsElectrical Requirements Venting RequirementsCalculating Vent System Length Installation InstructionsVenting Methods Downdraft Vent System PreparationVent Collar and Vent Transition Installation Install Downdraft Vent SystemPrepare for Mounting the In-Line Blower System Install Downdraft Vent In-Line External Type Blower MotorPrepare the In-line Blower System Inlet Side Install In-line Blower System Outlet SideComplete Preparation Electrical Connection Inside In-line Blower System Make Electrical Connections for In-Line Blower Motor SystemGrounding Instructions Complete InstallationDowndraft Mounted Controls Remote Up/Down SwitchDowndraft Vent System USE Operating Downdraft Vent SystemRemote Control Operation Filters Vent System CareSurface of Downdraft Vent GlassReplacing the Fuse User Servicing InstructionsSEL0053854 DiagramwiringU.S.A Assistance or ServiceJENN-AIRMAJOR Appliance Warranty AccessoriesCall This limited warranty does not coverVotre sécurité et celle des autres est très importante Sécurité DU Système DE VentilationImportantes Instructions DE Sécurité Exigences d’emplacement Exigences DinstallationOutillage et pièces Plan de travail Dimensions des ouvertures à découper Dimensions du produit Dimensions du placardExigences concernant l’évacuation Longueur recommandée du circuit d’évacuationInstallations dans les régions au climat froid Spécifications électriquesCalcul de la longueur du circuit d’évacuation Instructions D’INSTALLATIONMéthodes d’évacuation Préparation du système dextraction Par le basInstallation du système dextraction Par le bas Préparation du système de ventilation en ligne Préparation du montage du système de ventilation en ligneAchever la préparation Installation du système de ventilation en ligneCôté sortie Côté entréeSerrer les vis du bornier Déconnecter la source de courant électriqueInstructions de liaison à la terre Achever l’installationCommutateur de montée/descente déporté Commandes montées sur lextracteurFonctionnement du système dextraction Par le bas Utilisation du système dextraction par le basFonctionnement de la télécommande Vitre Remplacement des piles de la TélécommandeEntretien DU Système Dextraction Surface du système dextraction par le basInstructions DE Dépannage Pour Lutilisateur Remplacement du fusibleGris CdsâblageechémaSi vous avez besoin de pièces de rechange Assistance OU ServiceAccessoires Au CanadaLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers JENN-AIRPage W10526413C

LIB0057678, W10526413C specifications

The Jenn-Air W10526413C, LIB0057678 is a high-performance kitchen appliance designed to elevate culinary experiences and enhance kitchen aesthetics. This premium model is part of the renowned Jenn-Air brand, celebrated for its commitment to innovation, quality, and luxury in home appliances.

One of the standout features of the Jenn-Air W10526413C is its sophisticated design, seamlessly integrating into modern kitchens. With a sleek, stainless steel finish and elegant lines, it complements a variety of decors and adds a touch of sophistication to any cooking space. The appliance’s user-friendly interface includes intuitive controls, making it easy for home chefs to access a multitude of settings and features.

Key technologies incorporated in the Jenn-Air W10526413C include Smart Temperature Management, which ensures precise control over cooking temperatures, enabling users to achieve optimal results for a range of dishes. This technology also helps maintain consistent temperature levels, reducing cooking time and improving energy efficiency. Additionally, the appliance features advanced cooking modes such as convection baking, broiling, and roasting, allowing for versatility in meal preparation.

One of the highlights of this model is its powerful ventilation system, which efficiently eliminates smoke, steam, and odors from the kitchen. The integrated hood provides effective airflow, ensuring a clean and comfortable cooking environment. This is complemented by the appliance's quiet operation, which minimizes disruptions during meal prep and family gatherings.

The Jenn-Air W10526413C is designed with practicality in mind; it includes ample cooking space and adjustable racks that can accommodate various dish sizes and cooking methods. The appliance's durable construction guarantees longevity, making it a worthwhile investment for any home cook or culinary enthusiast.

Moreover, the Jenn-Air W10526413C supports Wi-Fi connectivity, enabling users to control and monitor the appliance remotely through their smartphones or smart home systems. This feature not only enhances convenience but also allows for seamless integration into modern smart kitchens.

Overall, the Jenn-Air W10526413C, LIB0057678 is a remarkable addition to any kitchen, combining cutting-edge technology, elegant design, and versatility. Whether you are preparing a simple weeknight dinner or hosting an elaborate gathering, this appliance is engineered to meet the demands of any culinary endeavor while adding a touch of luxury to your cooking experience.
Top Page Image Contents