Install Range Hood, Complete Preparation

Optional Duct Cover Installation

1.Attach the full-width duct cover to the top of the range hood with the screws provided with duct covers. The duct cover must be attached to the top of the range hood before mounting the range hood to the wall. For information on ordering the optional duct cover, see the “Accessories” section.

Complete Preparation

1.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the range hood. See the “Venting Requirements” section.

2.Determine the location where the power supply cable will be run through the wall.

3.Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4.Pull enough power supply cable through the wall to allow for easy connection to the terminal box.

5.Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent transition with damper to top of the range hood using 4 - 3.5 x 9.5 mm screws.

6.Remove terminal box cover and set aside.

7.Remove knockout from the back of the vent hood and install a UL listed or CSA approved ¹⁄₂" strain relief. See “Make Electrical Connection” section.

8.Place the range hood near its mounting position and run the power supply cable through the strain relief into terminal box (enough to make connection).

9.Tighten the strain relief screws.

Install Range Hood

The hood attaches to the wall by the 2 mounting screws in the wood support mounted to the wall in the “Range Hood Mounting Screws Installation” section.

1.Using 2 or more people, hang the range hood on the wall by placing the slotted holes in the range hood back over the

2 screws mounted to the wood support mounted to the wall.

NOTE: If your installation uses the optional duct cover, the vent system needs to be connected to the hood and the duct cover mounted to the top of the range hood before tightening the mounting screws. See steps 5 and 6.

→

4.Install 4 - 4.2 x 19 mm screws through the back of the hood into the wood support and tighten.

5.Connect vent system to hood. Seal all joints with clamps.

6.If your installation uses the optional duct cover, mount it to the top of the range hood following the instructions supplied with the duct cover.

Install Range Hood Blower Motor

1.Install the range hood blower motor assembly inside the hood canopy with the wiring to the left.

A. Blower motor

2.Slide the left mounting plate flange under the bracket.

A.Bracket

B.Mounting plate flange

3.Push the right end of the mounting plate up and snap into spring tab.

NOTE: The spring tab should be outside of the slot in the mounting plate.

2.Push the range hood up into the narrow slots, align the bottom of the hood to the horizontal line, level the hood, and

	tighten the 2 mounting screws.	A
	3. Mark 2 lower mounting hole locations. Drill ¹⁄₈" pilot holes if	A
	the holes are located into wood. If holes are not located into
	wood, remove the hood and drill two ³⁄₈" pilot holes and insert
	10 x 50 mm wall anchors. Remount the hood, level, and
	tighten the upper screws. Install 2 - 6 x 80 mm screws into	A. Spring tab
	the lower mounting anchors and tighten.	A. Spring tab
	the lower mounting anchors and tighten.

LI3UNB, W10274316B specifications

The Jenn-Air LI3UNB, W10274316B, represents a pinnacle of performance and elegance in the realm of kitchen appliances. This powerful kitchen solution combines advanced technology with sophisticated design, making it an ideal choice for culinary enthusiasts and home chefs alike.

One of the standout features of the Jenn-Air LI3UNB is its highly efficient cooling system. Designed with an advanced compressor and evaporator, this model ensures consistent temperature regulation, keeping food fresher for longer. The unit's customizable temperature settings allow users to efficiently store a variety of items, from vegetables to fine wines, catering to diverse storage needs.

In addition to its cooling efficiency, the LI3UNB boasts a sleek, modern aesthetic that integrates seamlessly into any kitchen décor. Its stainless steel finish is not only visually appealing but also resistant to smudges and fingerprints, ensuring that the appliance maintains its luxurious appearance over time. The minimalist design is complemented by hidden hinges, providing a clean, unobtrusive look.

The LI3UNB model is engineered for convenience, featuring adjustable shelving that offers flexibility in storage configurations. Users can easily accommodate taller items such as wine bottles or large platters, enhancing organizational capabilities. Furthermore, the built-in LED lighting illuminates its interior, making it easy to find what you need without rummaging through.

Technologically, the Jenn-Air LI3UNB is equipped with smart features that elevate its functionality. Some models come with Wi-Fi connectivity, enabling users to control and monitor their appliance remotely. This means that whether you’re away from home or lounging on the couch, you can adjust temperatures or receive alerts about any potential issues, adding an extra layer of peace of mind to your food storage.

Moreover, the LI3UNB embraces energy efficiency. It operates quietly while consuming significantly less energy compared to older models, making it environmentally friendly while also helping to reduce utility bills.

For those who appreciate culinary excellence, the Jenn-Air LI3UNB, with its combination of style, performance, and smart technology, is a remarkable choice. It redefines what users should expect from kitchen appliances, elevating everyday cooking and food preservation experiences to extraordinary heights.