Installation Requirements, Tools and Parts

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■Level

■Drill

■1¼" (3 cm) drill bit

■¹⁄₈" (3 mm) drill bit if installing into wood and a ⁵⁄₁₆" (8 mm) drill bit if installing optional backsplash kit.

■Pencil

■Wire stripper or utility knife

■Tape measure or ruler

■Pliers

■Caulking gun and weatherproof caulking compound

■Vent clamps

■Jigsaw or keyhole saw

■Flat-blade screwdriver

■Metal snips

■Phillips screwdriver

■Scissors

Parts needed

■Home power supply cable

■1 - ½" (12.7 mm) UL listed or CSA approved strain relief

■3 UL listed wire connectors

■1 wall or roof cap

■Metal vent system

Parts supplied

Remove parts from packages. Check that all parts are included.

■2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

4 metal grease filters for 48" (121.9 cm) models

■Damper

■Hood canopy with blower and halogen lamps installed.

■1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct transition.

■2 - 175 watt infrared heat lamps

■Wood support

■Grease collectors

■4 - 6 x 80 mm mounting screws

■4 - 3.5 x 9.5 mm screws

■6 - 4.2 x 19 mm screws

■5 - M6 x 16 mm screws

■5 - D6.4 x 11 mm washers

■2 - D5.3 x 20 mm washers

■2 - 10 x 50 mm wall anchors

■T20® TORX®†adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall of the range hood.

Canopy range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof or through the wall.

All openings in ceiling and wall where canopy range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Front view

18¹⁄₁₆" (45.9 cm) for 48" (121.9 cm) Hood 12¹⁄₁₆" (30.6 cm) for 36" (91.4 cm) Hood 9¹⁄₁₆" (23.0 cm) for 30" (76.2 cm) Hood

6¹⁄₂" (16.5 cm)

12" (30.5 cm)

18" (45.7 cm)

2¹⁄₄"

(5.7 cm) 25" (63.5 cm)

30" (76.2 cm) 36" (91.4 cm)

48" (121.9 cm)

†®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

LI3UNB, W10274316B specifications

The Jenn-Air LI3UNB, W10274316B, represents a pinnacle of performance and elegance in the realm of kitchen appliances. This powerful kitchen solution combines advanced technology with sophisticated design, making it an ideal choice for culinary enthusiasts and home chefs alike.

One of the standout features of the Jenn-Air LI3UNB is its highly efficient cooling system. Designed with an advanced compressor and evaporator, this model ensures consistent temperature regulation, keeping food fresher for longer. The unit's customizable temperature settings allow users to efficiently store a variety of items, from vegetables to fine wines, catering to diverse storage needs.

In addition to its cooling efficiency, the LI3UNB boasts a sleek, modern aesthetic that integrates seamlessly into any kitchen décor. Its stainless steel finish is not only visually appealing but also resistant to smudges and fingerprints, ensuring that the appliance maintains its luxurious appearance over time. The minimalist design is complemented by hidden hinges, providing a clean, unobtrusive look.

The LI3UNB model is engineered for convenience, featuring adjustable shelving that offers flexibility in storage configurations. Users can easily accommodate taller items such as wine bottles or large platters, enhancing organizational capabilities. Furthermore, the built-in LED lighting illuminates its interior, making it easy to find what you need without rummaging through.

Technologically, the Jenn-Air LI3UNB is equipped with smart features that elevate its functionality. Some models come with Wi-Fi connectivity, enabling users to control and monitor their appliance remotely. This means that whether you’re away from home or lounging on the couch, you can adjust temperatures or receive alerts about any potential issues, adding an extra layer of peace of mind to your food storage.

Moreover, the LI3UNB embraces energy efficiency. It operates quietly while consuming significantly less energy compared to older models, making it environmentally friendly while also helping to reduce utility bills.

For those who appreciate culinary excellence, the Jenn-Air LI3UNB, with its combination of style, performance, and smart technology, is a remarkable choice. It redefines what users should expect from kitchen appliances, elevating everyday cooking and food preservation experiences to extraordinary heights.