Installation Instructions

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

Prepare Location

■It is recommended that the vent system be installed before hood is installed.

■If you are installing the optional backsplash with shelves for heat lamps, follow the instructions included with that product.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check that all installation parts have been removed from the shipping carton.

1.Disconnect power.

2.Determine which venting method to use: roof or wall exhaust.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

The hood is attached to the wall with the wood support that is attached to the back of the hood.

1.Determine and mark the centerline on the wall where the canopy range hood will be installed.

2.Select a mounting height between a minimum of 30"

(76.2 cm) and a suggested maximum of 36" (91.4 cm), above the cooking surface and the bottom of the range hood and mark a horizontal reference line on the wall.

3.Remove the wood support from the back of the range hood by loosening the 2 screws from the inside. Locate and level the top of the wood support 15³⁄₈" (39.1 cm) above the marked horizontal line and centered on the vertical centerline. Using 2 - 4 of the 6 x 80 mm screws, install wood support so that it is screwed into at least 2 vertical studs.

15³⁄₈"
(39 cm)	A

30" (76.2 cm) to 36" (91.4 cm)

A. Wood support

B. Centerline

NOTE: The screws provided for mounting this hood must be fastened into solid wood. Do not fasten into sheet rock only.

LI3UNB/W10274316B specifications

Jenn-Air LI3UNB/W10274316B is an innovative kitchen appliance that brings a sophisticated touch to modern cooking. Designed for discerning culinary enthusiasts, this built-in refrigerator embodies luxury, style, and advanced technology.

One of the standout features of the Jenn-Air LI3UNB is its impressive capacity. With a spacious interior, it provides ample room for all your food and beverages. Its flexible shelving and storage options allow you to configure the layout according to your needs, accommodating everything from tall bottles to small jars.

This refrigerator is equipped with advanced cooling technologies, including the Dual Evaporator system. By utilizing separate evaporators for the refrigerator and freezer compartments, it ensures optimal humidity levels and prevents odor transfer between sections. This technology maintains the freshness of food for longer periods, allowing you to shop for groceries less frequently while enjoying the quality of your ingredients.

The exterior of the LI3UNB is just as striking as its interior. With a sleek and stylish stainless-steel finish, it seamlessly integrates into any kitchen design, exuding elegance and modernity. The appliance comes with an integrated ice maker, offering the convenience of fresh ice without the need for bulky ice trays.

Control is made effortless with the intuitive digital interface, providing users with an easy way to set temperatures, activate functions, and monitor the refrigerator’s performance. The bright interior LED lighting illuminates every corner, allowing for easy visibility of stored items, even when it's packed full.

Energy efficiency is another significant attribute of the Jenn-Air LI3UNB/W10274316B. The appliance meets stringent energy standards, contributing to lower utility bills while minimizing environmental impact. Its Energy Star rating ensures that it operates efficiently without compromising on performance.

In addition to its functional features, the LI3UNB also boasts an ultra-quiet operation, making it an ideal choice for open-concept living spaces. The carefully engineered compressor and cooling system allow it to run quietly, ensuring that it doesn’t disrupt your home environment.

In summary, the Jenn-Air LI3UNB/W10274316B is more than just a refrigerator; it’s a sophisticated appliance designed to meet the needs of today’s modern kitchens. With its spacious design, advanced cooling technologies, energy efficiency, and elegant aesthetics, it stands out as a premium choice for anyone looking to enhance their culinary experience.